Related Manuals for Amphenol H4 Cable Series
Summary of Contents for Amphenol H4 Cable Series
- Page 1 H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L Amphenol 太阳能连接器H4线端系列安装手册 PV Connector H4 Cable Series Instruction Manual H4-H 太阳能线端连接器 H4 太阳能线端连接器 H4-H PV CABLE CONNECTOR H4 PV CABLE CONNECTOR...
-
Page 2: Table Of Contents
H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 目 录 Table of Contents 1. 警告 4. 组装流程 Caution Assembly process 2. 技术参数 4.1 线端连接器组装 Technical data Cable connectors assembly 3. 工具及应用 Tools & application 4.2连接器对插及解锁 Connectors mating and un-mating 3.1 工具... -
Page 3: 警告
The use of tin plated cable is recommended. 5) 安费诺连接器配合状态符合IP68（水下1米一小时）密封性能。 The Amphenol connectors being mated are IP68 compliant in the function of sealing, and can be positioned for underwater 1 meter an hour 6) 该产品应由有相应资质或经过专家培训的、具备相关安全应用规范的专业人员安装。 The product may be assembled and installed only by suitably qualified and trained specialists with due observance of applicable safety regulations 7) 该连接器只适用于B类和C类的铜导线(参考NFPA NEC 70第9章,表格10)。如果与其他等级的铜导线使用，连接器应做标记。参考电缆导体标准：... -
Page 4: 技术参数
连接并产生损害，对此我们不承担任何责任。 Connectors not made by Amphenol which can be mated with Amphenol elements and in some cases are also described as “Amphenol-compatible”do not conform to the requirements for safe electrical connection with long-term stability, and for safety reasons must not be plugged together with Amphenol elements .Amphenol can therefore accept no liability for damage which occurs as a result of mating these connectors which lack Amphenol approval... -
Page 5: 工具及应用
H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 3.工具及应用 Tools & application 3.1)工具: Required tools 机加工端子钳口: 机加工端子压接钳: Crimping die for cold forming contact: Crimp tool for cold forming contact （2.5/4.0/6.0/10mm²端子） （2.5/4.0/6.0/10mm²端子） UTXTC0004 UTXTD0004 (for 2.5/4/6/10mm² contact) (for 2.5/4/6/10mm² contact) -
Page 6: 剥线流程
使用安费诺剥线工具(H4TS0000)剥线时，首先调整卡位将线材放置合适位置，剥去线皮长度7.0±0.5 mm。注意不要伤及铜丝, 见下图3.2.1到图3.2.3。 Amphenol specified strip tool (H4TS0000) can be used in this step. First adjust the striper stopper ,then put the cable in corresponding notch to strip the length of 7±0.5mm. Strip cable are carefully not to nick conductors. See below pictures3.2.1 to 3.2.3. -
Page 7: 冲压端子压接流程
正确的定位器孔位，小心不要伤到定位翅膀，见图 3.4.1至图3.4.5. 压接后端子电缆拔出力要求需要满足表3.4.1要求， Amphenol specified crimp tool (H4TC0003) can be used in this step. Insert striped cable into contact barrel and Insure all conductor strands are captured in the contact barrel. Crimp contact barrel by using the crimping die, Be careful for not hurting the locator wings. See below pictures 3. 4.1 to 3.4.5. The pull-out force should meet below table 3.4.1 requirement. -
Page 8: 组装流程
H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 客户使用自动打端子机进行压接时, 建议的压接规范, The customer wants to use the automatic crimping machine, we suggest that the contact crimping spec 电缆规格 铆接宽度(B) 铆接高度(A) Cable Size Crimping Width(B) Crimping Height(A) 14AWG/2.5 mm² 2.10mm REF 3.40mm REF... - Page 9 H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 白色区域/White area 连接器边需要在白色区域中间 图 4.1.5 Edge of connector should be Picture 4.1.5 in the middle of white area. 图 4.1.6 4.1.2) 锁紧螺帽 Picture 4.1.6 Tightening the back cap H4及H4-H连接器锁紧螺帽的扭矩：2.6 N·m 到2.9 N·m。...
- Page 10 客户用扭力扳手组装连接器时，可使用安费诺专用连接器套筒进行组装(H4和H4-H使用H4TTW100)。如图4.1.10及图4.1.11 Amphenol specified wrench tool (H4TW0001 for H4&H4-H and H4TW0004 for Enlarge H4) can be used in this step See below picture 4.1.8 and 4.1.9. Customer can use open-end back cap spanner (H4 use H4TTW100) if customer use electric torque controlled wrench tool to tighten the cap，as below picture4 .1.10 and 4.1.11.
-
Page 11: Connectors Mating And Un-Mating
公端和母端连接器对插直到听到“滴“的卡位声说明对插到位。安费诺H4连接器符合NEC 2008 690.33标准, 所以需要工具进行解锁。 For mating, align the 2 half connectors and mate them together by hand until a “click” is heard and/or felt. For un-mating, since the Amphenol H4 complies with the NEC 2008 690.33, a tool is required to disconnect the connector once mated. - Page 12 H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 连接器选型： Connector order number: How to Order a Connector (please choose one code per position, below) Connector Product Product Type Gender Cable Size Certifications Packaging Contact Type Type Line Without Contact 1 pc/bag S&F...
-
Page 13: 电缆状态
H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 5. 电缆状态: Cable routing 电缆根部建议保留20mm未折弯长度，以免因线缆折弯产生的外力引起连接器密封件变形. 如图5.1和图5.2。 In order to avoid the cable bend force lead to a visible deformation in the sealing portion of the insulation, the cable need keep at least 20mm straight length. -
Page 14: 存储注意事项
H4 CABLE SERIES INSTRUCTION MANUAL 文件编号(File Name) :WI-S037-ENG REV.L 7. 存储注意事项： Note on storage： 我们建议连接器零件的存储温度为-30℃-+60℃，相对湿度低于70%。连接器零件不能暴露在因直接降雨、冷凝等带来的水汽中。确保零件不能与酸、碱、瓦斯、 丙酮或者任何其他会影响材料使用的化学物质接触。如果以上条件得到满足，连接器的零件存储时间长达两年时间。 We recommend that you store connector components at temperature between-30℃to +60℃ and with a relative humidity of less than 70%.The components must not be exposed to moisture due to direct rainfall ,condensation .etc ,Ensure that the individual components do not come into contact with acids, alkalis, gases, acetone or any other chemical substance that could impact the materials use .If these condition are met. - Page 16 Amphenol Technology (Shenzhen) Co., Ltd Tel: +86-755-29918389 Email：info@amphenol-industrial.com web: www.amphenol-sustainable.com Block C, Xia Shi Jia 2nd Industrial Estate, Gongming, Shenzhen, 518106, China...
Need help?
Do you have a question about the H4 Cable Series and is the answer not in the manual?
Questions and answers