Zennio MAXinBOX 66 Manual
  1. Manuals
  2. Brands
  3. Zennio Manuals
  4. Controller
  5. MAXinBOX 66
  6. Manual

Zennio MAXinBOX 66 Manual

Multifunction actuator with 6 outputs and 6 inputs
Hide thumbs Also See for MAXinBOX 66:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
MAXinBOX 66
Multifunction Actuator with 6 Outputs and 6 Inputs
ZN1IO-MB66
Application program version: [1.4]
User manual edition: [1.4]_a
www.zennio.com

Advertisement

Table of Contents
loading

Related Manuals for Zennio MAXinBOX 66

Summary of Contents for Zennio MAXinBOX 66

  • Page 1  MAXinBOX 66 Multifunction Actuator with 6 Outputs and 6 Inputs ZN1IO-MB66 Application program version: [1.4] User manual edition: [1.4]_a www.zennio.com...

  • Page 2: Table Of Contents

    MAXinBOX 66 CONTENTS Contents ............................2 Document Updates ........................3 Introduction .......................... 4 1.1 MAXinBOX 66 ........................4 1.2 Installation ........................5 1.3 Start-Up and Power Loss ....................6 Configuration......................... 7 2.1 General ..........................7 ETS Parameterisation ....................7 2.2 Inputs ..........................9 2.2.1...

  • Page 3: Document Updates

    MAXinBOX 66 DOCUMENT UPDATES Version Changes Page(s) Changes in the application program:  [1.4]_a Optimisation of the outputs, inputs, logic functions, thermostat and master light modules. Changes in the application program:  Heartbeat functionality added.  Optimisation of the outputs, inputs, logic functions, thermostat and master light modules.

  • Page 4: Introduction

    MAXinBOX 66 1 INTRODUCTION 1.1 MAXINBOX 66 MAXinBOX 66 from Zennio is a versatile KNX actuator featuring a wide variety of functions: 6 relay outputs, configurable as:  Up to 3 independent shutter channels (with or without slats),  Up to 6 individual ON/OFF outputs, ...

  • Page 5: Installation

    MAXinBOX 66 1.2 INSTALLATION MAXinBOX 66 connects to the KNX bus through the on-board KNX connector. Once the device is provided with power from the KNX bus, both the individual address and the associated application program may be downloaded. This device does not need any additional external power since it is entirely powered through the KNX bus.

  • Page 6: Start-Up And Power Loss

    Please consult the next sections of this document for further details. On the other hand, when a bus power failure takes place, MAXinBOX 66 will interrupt any pending actions, and will save its state so it can be recovered once the power supply is restored.

  • Page 7: Configuration

    MAXinBOX 66 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by right-clicking into the device and selecting Edit parameters. ETS PARAMETERISATION The only parameterisable screen available by default is General. From this screen it is possible to activate/deactivate all the required functionality.
  • Page 8 MAXinBOX 66 power failure). It is possible to parameterise a certain delay to this sending (0 to 255 seconds). Figure 3. Sending of Indication objects on bus voltage recovery Heartbeat (Periodical Alive Notification): this parameter lets the integrator incorporate a one-bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be sent periodically with value “1”...

  • Page 9: Inputs

    It is possible to connect motion detectors (models ZN1IO-DETEC-P and ZN1IO- DETEC-X from Zennio) to the input ports of MAXinBOX 66. This brings the device with the possibility of monitoring motion and presence in the room, as well as the light level.
  • Page 10 Motion detectors with references ZN1IO-DETEC and ZN1IO-DETEC-N are not compatible with MAXinBOX 66 (may report inaccurate measurements if connected to this device). When connected to MAXinBOX 66, the rear micro-switch of model ZN1IO- DETEC-P should be set to position “Type B”. http://www.zennio.com Technical Support: http://support.zennio.com...

  • Page 11: Outputs

    Individual outputs. Shutter channels. 2.3.1 MANUAL CONTROL MAXinBOX 66 allows manually switching the state of its output relays through the respective pushbuttons on the top of the device. A specific pushbutton is therefore available per output. Manual operation can be done in two different ways, named as Test On Mode (for testing purposes during the configuration of the device) and Test Off Mode (for a normal use, anytime).
  • Page 12 MAXinBOX 66 that moment, once the button is released, the LED light will remain green to confirm that the device has switched from the Test Off mode to the Test On mode. After that, an additional press will turn the LED yellow and then off, once the button is released.
  • Page 13 MAXinBOX 66 Regarding the lock, timer, alarm and scene functions, the device will behave under the Test Off mode as usual. Button presses during this mode are entirely analogous to the reception of the corresponding orders from the KNX bus.

  • Page 14: Ets Parameterisation

    MAXinBOX 66 ETS PARAMETERISATION The Manual Control is configured from the Configuration tab itself under Outputs. The only two parameters are: Figure 5. Manual Control Manual Control: options are “Disabled”, “Only Test Mode Off”, “Only Test Mode On” and “Both Test Mode Off and On” (default). Depending on the selection, the device will permit using the manual control under the Test Off, the Test On, or both modes.

  • Page 15: Logic Functions

    KNX bus, and to send the results through other communication objects specifically enabled for this purpose. MAXinBOX 66 can implement up to 10 different and independent functions, each of them entirely customisable and consisting in up to 4 consecutive operations each.

  • Page 16: Thermostats

    MAXinBOX 66 2.5 THERMOSTATS MAXinBOX 66 implements four Zennio thermostats which can be enabled and configured independently. Please refer to the specific “Zennio Thermostat” user manual available under the MAXinBOX 66 product section at the Zennio homepage (www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.

  • Page 17: Master Light

    The Master Light function brings the option to monitor the state of up to 12 light sources (or even more, if the Master Light controls from multiple Zennio devices are linked together) or of any other elements whose state is transmitted through a binary object and, depending on those states, perform a master order every time a certain trigger signal (again, a binary value) is received through a specific object.
  • Page 18 MAXinBOX 66 Number of State Objects: defines the number of 1-bit status objects required. The minimum (and default) value is “1”, and the maximum is “12”. These objects are called “[ML] Status Object n”. In addition, the general status object (“[ML] General status”) will always be available in the project topology.
  • Page 19 MAXinBOX 66 Courtesy Switch-On: The parameters available here are entirely analogous to those already mentioned for General Switch-Off. However, in this case the names of the objects start with “[ML] Courtesy Switch-On (…)”. On the other hand, sending scene save orders is not possible for the courtesy switch-on (only orders to play scenes are allowed).

  • Page 20: Scene Temporisation

    MAXinBOX 66 2.7 SCENE TEMPORISATION The scene temporisation allows imposing delays over the scenes of the outputs. These delays, defined in parameters, are applied on the execution of one or more scenes that may have been configured. Please bear in mind that, as multiple delayed scenes can be configured for each...
  • Page 21 MAXinBOX 66 Figure 8. Configuring Scene Temporisations Therefore, parameter “Scene m. Z Delay” defines the delay that will be applied to the action defined in Z (being Z a specific individual output or shutter channel) for the execution of scene m. The range of this delay is 0 to 3600 seconds, 0 to 1440 minutes or 0 to 24 hours http://www.zennio.com...

  • Page 22: Annex I. Communication Objects

    MAXinBOX 66 ANNEX I. COMMUNICATION OBJECTS “Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself.
  • Page 23 MAXinBOX 66 N.C. (0=Close Relay; 1= 1 Bit C - - W - DPT_BinaryValue [Ox] On/Off Open Relay) 0=Output Off; 1=Output 89, 97, 105, 113, 121, 129 1 Bit C T R - - DPT_BinaryValue [Ox] On/Off (Status) 90, 98, 106, 114, 122, 130...
  • Page 24 MAXinBOX 66 ] Direct Positioning 2 0=No Action; 1=Save  153, 170, 187 1 Bit C - - W - DPT_Ack (Save) Current Position 1 Byte C - - W - DPT_SceneControl 0-63; 128-191 [Thermostat] Scene Input Scene Value External Sensor...
  • Page 25 MAXinBOX 66 211, 241, 271, 301 1 Byte C T R - - DPT_Scaling 0% - 100% [Tx] Control Variable (Cool) PI Control (Continuous) 212, 242, 272, 302 1 Byte C T R - - DPT_Scaling 0% - 100% [Tx] Control Variable (Heat)
  • Page 26 MAXinBOX 66 332, 336, 340, 344, 348, 352 1 Bit C T R - - DPT_Alarm [Ix] Overcooling 0 = No Alarm;1 = Alarm 333, 337, 341, 345, 349, 353 1 Bit C T R - - DPT_Alarm [Ix] Overheating 0 = No Alarm;1 = Alarm...
  • Page 27 MAXinBOX 66 … 0xF (Inc. by 1%) 0x0 (Stop) 0x1 (Dec. by 100%) … 0x7 (Dec. by 1%) [Ix] [Short Press] 4 Bit C T - - - DPT_Control_Dimming Switch Bright/Dark 0x8 (Stop) Brighter/Darker 0x9 (Inc. by 100%) … 0xF (Inc. by 1%)
  • Page 28 MAXinBOX 66 Up Shutter [Ix] [Long Press] Stop/Step Sending of 1 (Stop/Step 1 Bit C T - - - DPT_Step Down Shutter Down) [Ix] [Long Press] Stop/Step Switching of 0/1 1 Bit C T - - - DPT_Step Shutter (Switched)
  • Page 29 MAXinBOX 66 [Ix] [Long Press] Constant 1 Byte C T - - - DPT_Value_1_Ucount 0 - 255 0 - 255 Value (Integer) 1 Bit C T - - - DPT_Switch [Ix] [Double Press] 0 Sending of 0 1 Bit C T - - -...
  • Page 30 MAXinBOX 66 0 = Nothing; 1 = Detection 400, 429, 458, 487, 516, 545 1 Bit C - - W - DPT_Ack [Ix] Presence: Slave Input from slave device 401, 430, 459, 488, 517, 546 2 Bytes C - - W -...
  • Page 31 Join and send us your inquiries about Zennio devices: http://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. www.zennio.com info@zennio.com...

Table of Contents