Table of Contents
Advertisement
1-11. Setting the On-Board Switches and Description of LEDs
1-11-2. MX-103 Board (HKS-5830M)
7
6
5
D11
D10
D3001
D3002
D3003
D3201
D3051
D3052
D3053
D3054
D3055
D3056
D3057
D3068
D3058
D3069
D3059
D3070
D3060
D3071
D3061
D3072
D3062
D3073
D3063
D3074
D3064
D3075
D3065
D3076
D3066
D3077
D3067
D3078
D3079
D3080
D3081
D3082
D3083
D3084
<LEDs>
D10, D11 (A-7) : + + + + + 3.3 V-1, + + + + + 3.3 V-2 LED
Lights on when +3.3 V power supply is normal.
D3001, D3002, D3003 (B-7) : CNO 1/CNO 2/CAS
Lights on when the power supply operation of the
connector board that is installed in the back of this board
and that of the cascade input board are normal. If the
power supply operation of the connector board and cascade
input board is abnormal, or if the connector board and
cascade input board are not installed, it lights off.
D3001 indicates status of the upper connector board
(CNO1). D3002 indicates status of the lower connector
board (CNO2). D3003 indicates status of the cascade input
board (CAS).
D3051 to D3084 (C-7, D-7) : OUT LED
Lights on when the respective channels of 1 to 34 are
outputting the signal. It turns off when the signal is not
output.
D3201 (B-7) : RE-CLOCKING DIAG LED
Lights on when all of the re-clocker ICs are set in the
normal operation setup. It turns off if any single channel is
not set in the normal operation setup.
n
The normal operation setup means the following status.
Re-clock :
ON (Bypass : OFF)
Bit rate selection : AUTO (Manual selection : OFF)
Mode :
SMPTE (DVB-ASI : OFF)
1-30 (E)
4
3
2
1
A
B
C
D
E
F
Side A (Component side)
<Switches>
S3101 (E-7) : Re-clocker IC setting switch 1
8-pin DIP switch
ON
1
2
3
4
5
6
Factory setting
(
indicates the switch lever position.)
BIT1 to BIT4 : Re-clock bypass switch
BIT1 : Setting OUTPUT1 through OUTPUT8
BIT2 : Setting OUTPUT9 through OUTPUT17
BIT3 : Setting OUTPUT18 through OUTPUT25
BIT4 : Setting OUTPUT26 through OUTPUT34
Used to bypass the re-clocking (waveform shaping) of
signal in units of 8 output channels or 9 output channels.
ON : Bypass ON (Re-clock OFF)
OFF : Bypass OFF (Re-clock ON)
m
. Set to "Bypass OFF" during normal operation.
If it is set to "Bypass ON", an error may occur in the
equipment connected to the lower layer (refer to "1-9.
System Connection") of the HDS-X5800.
. Bypass ON/OFF can be also set using the setup menu of
secondary station. However, the "Bypass ON" setting
has priority.
If "Bypass ON" is set by secondary station, setting of
"Bypass OFF" becomes invalid even if it is set by the
switch.
BIT5 to BIT8: DVB-ASI mode switch
BIT5 : Setting OUTPUT1 through OUTPUT8
BIT6 : Setting OUTPUT9 through OUTPUT17
BIT7 : Setting OUTPUT18 through OUTPUT25
BIT8 : Setting OUTPUT26 through OUTPUT34
Used to select the DVB-ASI mode when handling the
DVB-ASI signal in units of 8 output channels or 9 output
channels.
ON : DVB-ASI mode
OFF : SMPTE mode
m
. When the DVB-ASI mode is selected, the SMPTE
signals cannot be handled.
. The mode can be also set using the setup menu of
secondary station. However, the "DVB-ASI mode"
setting has priority.
If "DVB-ASI mode" is set by secondary station, setting
of "SMPTE mode" becomes invalid even if it is set by
the switch.
7
8
HDS-X5800
Advertisement
Table of Contents
