Cisco NCS 1002 System Setup And Software Installation Manual page 63

Perform System Upgrade and Install Feature Packages
No FPD image version upgrade is required if the status of the power module is CURRENT in the command
output.
Example:
sysadmin-vm:0_RP0# show hw-module fpd
Wed Feb
Location
-------------------------------------------------------------------------------
0/0
0/0
0/0
0/0
0/RP0
0/RP0
0/RP0
0/RP0
0/PM0
0/PM1
In the above example, the status of both power modules is NEED UPGD. This status confirms that an FPD
image version upgrade is required. If the power cable is not connected to a power module, the Running version
of the power module is displayed as 0.0.
Caution
Step 2
Use the show fpd package command to display the FPD image version you need for each hardware component.
Example:
sysadmin-vm:0_RP0# show fpd package
Wed Feb
=============================== ================================================
Card Type
=================== ========================== ====== ======= ======== =========
NCS1002
--------------------------------------------------------------------------------
NCS1002
NCS1002--RP
--------------------------------------------------------------------------------
Step 3 Use the upgrade hw-module command to upgrade the FPD image of the power module.
Example:
The following example shows how to upgrade the FPD image of the power module.
sysadmin-vm:0_RP0# upgrade hw-module location 0/PM0 fpd PO-PriMCU
Step 4
Use the show hw-module fpd command to verify the upgraded firmware version of the power module.
28 03:35:09.566 UTC
Card type HWver FPD device
NCS1002-K9 0.1
NCS1002-K9 0.1
NCS1002-K9 0.1
NCS1002-K9 0.1
NCS1K-CNTLR 0.1
NCS1K-CNTLR 0.1
NCS1K-CNTLR 0.1
NCS1K-CNTLR 0.1
NCS1K-2KW-AC 0.0
NCS1K-2KW-AC 0.0
Ensure that both power cables are connected to the power modules during the upgrade procedure.
28 03:35:19.382 UTC
FPD Description
CTRL_BKP_LOW
CTRL_FPGA_LOW
CTRL_BKP_UP
CTRL_FPGA_UP
BIOS_Backup
BIOS_Primary
Daisy_Duke_BKP
Daisy_Duke_FPGA
Upgrading the Firmware Version of Power Modules
ATR Status
CTRL_BKP_LOW B CURRENT
CTRL_BKP_UP B CURRENT
CTRL_FPGA_LOW CURRENT
CTRL_FPGA_UP CURRENT
BIOS_Backup BS CURRENT
BIOS_Primary S CURRENT
Daisy_Duke_BKP BS CURRENT
Daisy_Duke_FPGA S CURRENT
PO-PriMCU NEED UPGD
PO-PriMCU NEED UPGD
Field Programmable Device Package
================================================
Req SW
Reload Ver
YES
YES
YES
YES
YES 14.00
YES 14.40
YES
YES
System Setup and Software Installation Guide for Cisco NCS 1002
FPD Versions
===============
Run Programd
2.23
2.23
2.23 2.23
2.23 2.23
14.00
14.40 14.40
0.15
0.17 0.17
0.00 0.00
0.00 0.00
Min Req Min Req
SW Ver Board Ver
2.23 2.23 0.1
2.23 2.23 0.1
2.23 2.23 0.1
2.23 2.23 0.1
14.00 0.1
14.40 0.1
0.15 0.15 0.1
0.17 0.17 0.1
59