Page 2
Stanza Wiring and Programming Guide Stanza Drives are available for control of Draperies and Roller Shades. Stanza Shades and Drapes can be controlled as part of a Stanza Integrated System, incorporating Stanza lighting controls, or as a Stanza Standalone System, without lighting controls. This Stanza Wiring and Programming Guide describes how to set up Stanza shades and drapes in both applications.
Table of Contents Page Basic Operation Keypad Functions IR Remote Functions Wiring Infrared Receiver Stanza Standalone System Stanza Integrated System 9-10 Contact Closure Contact Closure Specification Setting Limits From the Drive From an Infrared Remote 13-16 Programming Assigning Drive to Remote Control...
A maximum of 4 Shades or Drapes can be wired to any keypad output: • daisy chained or homerun Stanza Standalone System Keypads provide contact closures to the Shade or Drape, • and require no input power. Single Group Keypad...
Tapping any button while Shade or Drape is moving will cause it to stop • All Shades or Drapes with an IR receiver will respond to the Single Group IR Remote as shipped, • without any additional programming Page 4 Stanza Wiring and Programming Guide...
Close Bottom Group Same Functions as above All Stanza Drives with an IR receiver will respond to the Top Group of buttons without any • programming Shade or Drape Group Assignment is required to allow the Bottom Group of buttons to •...
Infrared Receivers Remote IR Eye Lutron offers a remote infrared eye for Stanza. It is a small dome connected to the Drive by a ® 22 in (560 mm) cable. The remote infrared eye plugs into a dedicated IR connector on the Drive. Ten foot extensions are available if the layout requires the IR eye to be located further from the Drive.
Single Drive Wiring Wire Type A IR Receiver 24 V Close Open Terminal block of Drive controlling single Shade or Drape Stanza Drapery or Single Group Roller Shade Drive Keypad Wire Type B Single group IR Transmitter SZ-PS-1-50 Power Supply Notes: Standalone shade or drapery drives can be controlled with a keypad, IR remote, or both.
24 V 24 V Close Receiver Close Open Open Terminal block of Drive controlled by Wire Type A Stanza Drapery or Group 1 buttons Roller Shade Drive Dual Group Keypad 24 V 24 V Close Close Open Optional IR Open...
Contact Closure Interface 24 V Close Open Wire Type A Terminal block of Drive controlling Stanza Drapery or single Shade or Roller Shade Drive Drape Wire Type B SZ-PS-1-50 Power Supply Notes: SZ-IO outputs programmed as a 0.25 second momentary contact closure output •...
SZ-PS-1-50 Power Supply SZ-IO Wire Type B 24 V Close Open Terminal block of Drive controlling Wire Type A Stanza Drapery or sheer Shade or Roller Shade Drive Drape 24 V Close Open Terminal block of Drive controlling blackout Shade...
Wire Type B SZ-PS-1-50 Power Supply Notes: The Stanza Drive accepts Class 2, dry contact closure inputs. The contact closure device • must be capable of switching 12 V at 4 mA. Momentary dry contact closure inputs require a minimum closure time of 0.25 seconds.
Green LED will turn on. Move the Shade or Drape to desired Close Limit by pressing arrow buttons. Press and hold the Close Limit button until the Green LED flashes. Close Limit is stored. Page 12 Stanza Wiring and Programming Guide...
• bottom Group prior to limit setting. Refer to Section 11 By default the Single Group IR Remote is assigned to all Stanza Drives and cannot • be reassigned to specific drives. Limits can be set at the Drive, or from the IR Remote.
Move Shade or Drape to desired Close Close Limit by pressing the Raise or Lower buttons. 10.8 Press and Hold the Close Limit Open Close button until the Green LED on the Drive flashes. Close Limit is stored. Page 14 Stanza Wiring and Programming Guide...
Page 16
Open Limit by pressing the Raise or Lower buttons. Open Close 10.12 Press and Hold the Open Limit button until the Green LED Open on the Drive flashes. Open Limit Close is stored. Open Close Page 15 Stanza Wiring and Programming Guide...
Page 17
Close Limit by pressing the Raise or Lower buttons. Open Close 10.16 Press and Hold the Close Limit button until the Green LED Open on the Drive flashes. Close Limit Close is stored. Open Close Page 16 Stanza Wiring and Programming Guide...
Each Shade or Drape in the system requires its own Infrared Receiver (SV-IR) • to allow it to be controlled via IR. By default the single Group IR Remote is assigned to all Stanza Drives and cannot • be reassigned to specific drives.
Note: If the LED on the Drive flashes orange in step 12.2, Programming lockout is enabled and favorite preset is not stored. Refer to Section 13 to disable and repeat steps 12.1 and 12.2. Page 18 Stanza Wiring and Programming Guide...
Note: If the LED on the Drive flashes orange in step 12.4, Programming lockout is enabled and favorite preset is not stored. Refer to Section 13 to disable and repeat steps 13.3 and 13.4. Page 19 Stanza Wiring and Programming Guide...
Favorite Preset button for 5 seconds. Open Close LED on the Drive will turn on steady Green then go out to indicate programming is unlocked. This will unlock all Drives assigned to the Top and Bottom Groups. Page 20 Stanza Wiring and Programming Guide...
LED flashes Green then turns on steady. 14.3 Press and hold CW arrow button until LED flashes Green then turns on steady. 14.4 Press and hold CCW arrow button until LED flashes Green then turns on steady. Page 21 Stanza Wiring and Programming Guide...
Note: Diagnostic mode will exit automatically after 5 minutes of inactivity. Pressing the addressing button will reset the inactivity time and the unit will remain in diagnostic mode. SZ-IO Rear View Contact Closure Outputs (CCO) Contact Closure Inputs (CCI) Page 22 Stanza Wiring and Programming Guide...
Not all Drives have their own IR Receiver Verify the voltage on the input terminal of the Drives not responding to Contact Stanza Drive. Voltage should be 9-10 V--- Closures from keypad, SZ-IO or third party between open/close and com when contact contact closure closure is not actuated.
If any manufacturing defect exists OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR in any of the components of a System other than the External Stanza Components, so long as Customer EXCLUSIONS MAY NOT APPLY TO YOU.