1. Manuals
  2. Brands
  3. Lutron Electronics Manuals
  4. Indoor Furnishing
  5. Sivoia QS roller 100
  6. Installation instructions manual

Lutron Electronics Sivoia QS roller 100 Installation Instructions Manual

Hide thumbs Also See for Sivoia QS roller 100:
Table of Contents

Advertisement

Quick Links

Download this manual
Sivoia
QS
®
roller 100
TM
wall mount
Installation
Instructions

Advertisement

Table of Contents
loading

Related Manuals for Lutron Electronics Sivoia QS roller 100

Summary of Contents for Lutron Electronics Sivoia QS roller 100

  • Page 1 Sivoia ® roller 100 wall mount Installation Instructions...

  • Page 2: Wall Mount

    1/4 in. Hex-Head Driver Wire Cutter/Stripper Level Pliers Power Drill #2 Phillips Screwdriver Box contents: (1) Sivoia QS roller 100 (2) Wall sub-brackets Left and right side shade brackets (1) 4-pin terminal block (attached) (8) Mounting screws (2) Extra retaining screws...
  • Page 3 CAUTION: Risk of bodily injury, follow all installation instructions. Notes: • The Sivoia QS roller 100 must be used only with shading systems approved by Lutron ® • There must be a clearance of at least 1.3 ft (0.4 m) between the fully lowered system and any permanent object.
  • Page 4 Confirm system dimensions Package Label Compare system dimensions on the package label with the window dimensions to verify appropriate window/shade combination. This information can also be found on the shade tube by lowering the fabric down far enough to expose the tube.
  • Page 5 Pre-drill for cable Determine where to drill for cable access. See options below. Cable should exit from wall, ceiling or jamb on EDU side of system. Note: Leave 12 to 18 in (305 to 457mm) of cable exposed. Wall Drill for cable 1.25 to 2 in (32 to 51 mm) from end of system and 2 in to 2.5 in (51 to 64 mm) from top of system.
  • Page 6 Mount Sub-Brackets Use fabric alignment holes to position the sub-bracket right to left. The fabric alignment holes will line up with the outside edge of the shade tube. Note: Fabric edge may not line up with the edge of the tube. Once their position has been established, mount sub-brackets using appropriate fasteners.
  • Page 7 Wire 4-pin terminal block Strip 2 in (51 mm) of the jacket off the cable run from the wall. 2 in (51 mm) Wire the 4-pin terminal block (provided) to the cable using a screwdriver. Make sure to tighten the screws tightly and that no insulation is inside of the terminal block. Notes: •...
  • Page 8 Mount the shade to sub-brackets NOTICE: Shades wider than 4 ft (1.2 m) require two people to install. Remove retaining screws from shade brackets. Note: Leave protective wrapping on shade during installation. Hook the lip of each shade bracket onto the top of each sub-bracket.
  • Page 9 Center and secure shade Move the shade left or right until centered. CAUTION: Risk of bodily injury Shade is not fully secured to the wall during the adjustment procedure. Shade must be supported by installer durimg adjustment procedure. Extreme movement from side-to-side may cause shade to fall.
  • Page 10 Adjust shade level Turn leveling screw to raise or lower idler side of shade until level. Adjust shade projection from window so that it clears any window trim or hardware when operating. Confirm roller tube turns freely without rubbing on anything.
  • Page 11 Connect terminal blocks Plug 4-pin terminal block on cable into EDU terminal block (a cable tie can be used to secure the terminal blocks together). Dress wires to ensure fabric does not rub while the shade is moving. Page 10 Sivoia roller 100 Wall Mount...
  • Page 12 Secure and check the shade Use the programming stylus to run the shade up and down using the adjustment buttons ( ). Re-level if needed. NOTICE: Pay careful attention to the shade roll up to ensure that it does not telescope extremely to one side or the other.
  • Page 13 Setting limits from the EDU Setting the open limit from the EDU The open and close limits define the top and bottom of the shade, and are used to determine which direction the shade must turn in order to raise or lower. Refer to the keypad instruction sheet to set the limits remotely.
  • Page 14 Setting limits from the EDU (continued) Setting the close limit from the EDU 10.4 Tap the “close limit” button ( ) . The green LED on the roller 100 EDU will turn on steady, Green LED indicating that the EDU is Tap the in “set close limit mode”.
  • Page 15 Verify Limits 11.1 Verify the open limit by double-tapping the “open limit” ( ) button. The shade will travel to the open limit. 11.2 Verify the close limit by double-tapping the “close limit” ( ) button. The shade will travel to the close limit. Page 14 Sivoia roller 100...

  • Page 16: Verify Communications

    Verify communications 12.1 Enter “link diagnostics mode” by pressing and holding the “close limit” button ( ) on the EDU for 5 seconds. The green LED will flash quickly for two seconds then turn Green LED on steady, indicating the EDU is ready to begin verifying communications with Press and hold the other devices.

  • Page 17: Restoring Default Settings

    Programming restoring default settings Returning an EDU to its factory default setting Returning an EDU to its factory defaults will clear out any programming to keypads, but will not affect the limits. 13.1 Press and hold the “close limit” button ( ) on the EDU for 5 seconds.

  • Page 18: Troubleshooting

    Troubleshooting Symptom Solution EDU is not powered - check EDU Power by unplugging and re-plugging in EDU. Shade will not move using adjustment LED should flash for 5 seconds. buttons on EDU. Shade is caught on something - free shade. Limits have been set incorrectly - refer to “Set open limit”...
  • Page 19 Notes: Page 18 Sivoia roller 100 Wall Mount Installation instructions ®...
  • Page 20 Notes: Page 19 Sivoia roller 100 Wall Mount Installation instructions ®...
  • Page 21 Notes: Page 20 Sivoia roller 100 Wall Mount Installation instructions ®...
  • Page 22 Notes: Page 21 Sivoia roller 100 Wall Mount Installation instructions ®...

  • Page 23: Limited Warranty

    Limited Warranty SCOPE hurricane or other problems beyond Lutron’s control; or (h) direct This limited warranty (“Warranty”) covers the Lutron supplied (a) exposure to corrosive materials. Sivoia QS Shade System (“Sivoia QS Shade System”), (b) Sivoia QED ® ® ® 2.

  • Page 24: Technical Assistance

    U.S. and foreign patents pending. FAX: +44.(0)20.7480.6899 Spain-Madrid Lutron, the Sunburst logo, Sivoia, and Sivoia QED are registered Technical support: TEL: +34.91.567.84.79 trademarks, and Sivoia QS is a trademark of Lutron Electronics Co., Inc. +44.(0)20.7680.4481 FAX: +34.91.567.84.78 FREEPHONE: 0800.282.107 FREEPHONE 0900.948.944 ASIAN...

Table of Contents