Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LaserLine GL3000P-E
Summary of Contents for LaserLine GL3000P-E
- Page 1 LaserLine Manufacturing, Inc. GL3000P-E OWnEr’s ManuaL Paint Striping Alignment Laser EU/IEC Version 1810 SE First Street, Suite H, Redmond, OR 97756, USA Phone 1 541 548 0882 • Fax 1 541 548 0892 • Email laserline@laserline.net Website www.LaserLineMfg.com REV. 12.28.17...
-
Page 2: Table Of Contents
Table of Contents system Overview: What it Does & How it Works Components & Controls Maintenance, service & Installation suggestions using the GL3000P-E Laser Extreme Temperature safety system GL3000P-E specifications Laser Emission Information GL3000P-E series Warranty Laser safety Considerations... -
Page 3: System Overview: What It Does & How It Works
The GL3000P-E Guidance Alignment Laser ThE SySTEM ThE ProducT The GL3000P-E Laser uses an ultra high visibility green • Main Housing — Weatherproof, containing optic plate laser to establish visual line control for your paint mounting platform, micro processor electronics, laser,... -
Page 4: Components & Controls
• Reverse voltage protected 11 Laser Control Cable 12 Emission Indicator Redundant Dual Red LED on Control Box and Laser. GL3000P-E LASEr 13 Laser Exit Window 14 Mounting Holes (4) Four holes provided to mount laser to stable surface. 15 Mil Spec Connector Connects control box to laser. -
Page 5: Maintenance, Service & Installation Suggestions
InSTALLATIon SuGGESTIonS The only maintenance that may be required is: 1. Mount the GL3000P-E Laser on the vehicle at least 5 feet off the ground. Most Operators prefer to mount the laser • Periodically clean the Exit Window of the GL3000P-E. -
Page 6: Using The Gl3000P-E Laser
ThE GL3000P-E LASEr uSInG ThE GL3000P-E 1. Turn the laser “On” 10 to 20 minutes prior to striping operation. This allows the GL3000P-E system to reach optimum operating temperature and power. Note: When outside air temperature is over 95˚ F (35˚ C), operate laser in “Blink”... -
Page 7: Extreme Temperature Safety System
ExTrEME TEMPErATurE SAFETy SySTEM The GL3000P-E has an internal cooling and heating sys- tem designed to allow the laser to operate at it’s maxi- mum potential. This system is also designed to protect the laser and your investment. In the event of extreme ambient heat (above 120˚ F, or 48.8˚... -
Page 8: Gl3000P-E Specifications
LaserLine Mfg., Inc. liability under this warranty is limited to repairing or replacing any product returned to an authorized service center for that purpose. any evidence of attempts to repair this unit by other than factory authorized personnel automatically voids the warranty. -
Page 9: Laser Safety Considerations
LASER OPERATOR TRAINING AND QUALIFICATION CARD LASER SAFETY CONSIDERATIONS reverse side of this card and is qualified to operate Laserline Post at least one LaserLine laser warning placard at each laser reverse side of this card and is qualified to operate Laserline Post at least one LaserLine laser warning placard at each laser Manufacturing, Inc. -
Page 10: Laser Safety
Service to be performed ONLY by manufacturer. beam can reflect back off the windshield into the Op- • Do not mount the GL3000P-E laser unit in a location erator’s eyes (backscatter). that allows the laser beam to be directed to hit any •... -
Page 11: Controls & Emissions
conTroLS & EMISSIonS 1 Master Power Switch Note: on left side. 3 amp fuse 2 Move Left 3 Move Right 4 Move Up 5 Move Down 6 Laser Mode Switch 1st depression = on steady mode 2nd depression = blink mode 3rd depression = laser off Key Switch Disconnects power. -
Page 12: Caution
cAuTIon! Do not expose this Laser to: • High pressure washing • Car wash When cleaning front window, use window cleaner with paper towel or clean cloth. no abrasives. Store in clean, dry environment when not in use.