Table of Contents
Advertisement
Quick Links
LaserLine Manufacturing, Inc.
GL3000PMC
OWNER'S MANUAL
Wing Plow & Guidance Alignment Laser
US Patent No. 7,966,753
US Patent No. 8,205,360
1810 SE First Street, Suite H, Redmond, OR 97756
Phone 541 548 0882 • Fax 541 548 0892 • Email laserline@laserline.net
Website www.LaserLineMfg.com
REV. 12.20.17
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LaserLine GL3000PMC
Summary of Contents for LaserLine GL3000PMC
- Page 1 OWNER’S MANUAL Wing Plow & Guidance Alignment Laser US Patent No. 7,966,753 US Patent No. 8,205,360 1810 SE First Street, Suite H, Redmond, OR 97756 Phone 541 548 0882 • Fax 541 548 0892 • Email laserline@laserline.net Website www.LaserLineMfg.com REV. 12.20.17...
-
Page 2: Table Of Contents
Section II Summer Operator’s Manual Summer Operation / Applications — System Overview: What It Does & How It Works Summer Maintenance, Service & Installation Suggestions Summer Use — Using the GL3000PMC Laser GL3000PMC Specifications GL3000PMC Warranty Section III Laser Safety Laser Safety Considerations Controls &... -
Page 3: Winter Operation Snow Plow Guide System Overview: What It Does & How It Works
5 seconds. for the exit window to reduce or eliminate ice build-up on the front of the laser output lens. The GL3000PMC also has Control Panel In Cab: Allows the operator to turn the a unique pneumatic snow removal system incorporated... -
Page 4: Operator Controls
(green light above laser mode switch) will the end. slow-blink until the system is warmed up, and then go on steady when the laser is activated. GL3000PMC LASER ASSEMBLY B Turn on the (3) Deicer Switch right after you Vertical Aiming Loosen to aim; retighten. -
Page 5: Winter Operation / Snow Plows Maintenance, Service & Installation Suggestions
Call the factory for details. 3. Do not mount the GL3000PMC laser unit in a location that allows the laser beam to be directed to hit any mir-... -
Page 6: Installation & Aiming The Laser For Snow Plows
INSTALLATION Underside of Mount the GL3000PMC Laser on the far right side (Fig. 1) Headache Rack Top of Cab (Only if rack is of the vehicle (passenger side) on top of the cab, on the attached to frame. -
Page 7: Snow Plow Operation
(see through) it. 3 The GL3000PMC laser spot puts your trailing edge lo- cation ahead of you and shows you what you will hit if you do not take action. -
Page 8: Operation: Straight, Outside Curve & Inside Curve
Straight Road Straight Road STRAIGHT ROAD As indicated Outside Curve OUTSIDE CURVE Outside Curve 800 Ft Radius More room than indicated 800 Ft Radius Inside Curve INSIDE CURVE Inside Curve Less room than indicated... -
Page 9: Summer Operation / Applications System Overview: What It Does & How It Works
Laser spot can be positioned to any desired location for line control Illustration of GL3000PMC being used to guide a paint striping rig — the same procedure is used for asphalt distributors, pavement profilers or any other operation requiring line guidance. -
Page 10: Summer Maintenance, Service & Installation Suggestions
INSTALLATION SUGGESTIONS The only maintenance that may be required is: 1. Mount the GL3000PMC Laser on the vehicle at least 5 feet off the ground. Most Operators prefer to mount the • Periodically clean the Exit Window of the GL3000PMC. -
Page 11: Summer Use Using The Gl3000Pmc Laser
SUMMER USE USING THE GL3000PMC LASER USING THE GL3000PMC 1 A) Turn on the Main Power Switch 15-20 minutes prior to use. This puts the laser module in “preheat” to get the laser up to operating temperature. The laser status light (green light above laser mode switch) will slow-blink until the system is warmed up, and then go off when the laser is ready to be activated. -
Page 12: Gl3000Pmc Specifications
LaserLine Mfg., Inc. liability under this warranty is limited to repairing or replacing any product returned to an authorized service center for that purpose. Any evidence of attempts to repair this unit by other than factory authorized personnel automatically voids the warranty. -
Page 13: Section Iii Laser Safety
LASER OPERATOR TRAINING AND QUALIFICATION CARD LASER SAFETY CONSIDERATIONS reverse side of this card and is qualified to operate Laserline Post at least one LaserLine laser warning placard at each laser reverse side of this card and is qualified to operate Laserline Post at least one LaserLine laser warning placard at each laser Manufacturing, Inc. -
Page 14: Controls & Emissions
Controls & Emissions CONTROLS & EMISSIONS ssion = Blink Mode Controls: sion = Off CONTROL PANEL ystem Power Switch with Red LED Indicator Removal Activation Switch with R aser Mode Switch with Green LED Indicator System Power Switch st depression = On Steady mode with Red LED Indicator ble to Vehicle 12Vdc nd depres... -
Page 15: Laser Safety
LASER SAFETY The GL3000PMC Laser is a Class IIIa Laser Product • Do not mount the GL3000PMC Laser in a location that generating less than 5 milliwatts of Laser Light. Class IIIa allows the laser beam to be directed to hit any shiny or...
Need help?
Do you have a question about the GL3000PMC and is the answer not in the manual?
Questions and answers