Subscribe to Our Youtube Channel
Related Manuals for OAKWORKS PX Series
Summary of Contents for OAKWORKS PX Series
- Page 1 USER MANUAL OAKWORKS ® PX & PT Tables PX Series PT Series made in the USA with US & imported parts www.oakworksmed.com · 717.235.6807...
- Page 2 ® damages in connection with or arising out of the furnishing, performance, or OAKWORKS is a registered use of this document and the program ® trademark of OAKWORKS , Inc. material which it describes. ®...
-
Page 3: Table Of Contents
Cleaning & Disinfection Recommended Cleaners/Disinfectants ..................26 Cleaning Process ..........................27 Inspections & Maintenance ........................27 Warranty Information ..........................27 Model Number & Serial Number PX Series ...............................28 PT Series ...............................29 Specifications Product Specifications ........................30 Environmental Conditions ......................30 Electrical Specifications ......................... 30 Guidance and manufacturer’s declaration -... -
Page 4: Product Use Description
PRODUCT USE DESCRIPTION / IMPORTANT SAFETY INSTRUCTIONS PRODUCT USE DESCRIPTION The Oakworks PX & PT Tables are used to support the patient during examinations and procedures. They are intended to be operated by a healthcare professional in a medical environment. No special training is required but a review of the following Safety Instructions is important for the safety of the operator and patient. - Page 5 3. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped damaged, or dropped into water. Contact Oakworks Customer Service before use. 4. Keep the cord away from heated surfaces.
-
Page 6: Product Description & Photo
PRODUCT DESCRIPTION PX100 Upholstered Top QuickLock™ Face rest with Boiance™ Crescent Self-locking molded rubber feet (2) Accessory attachment outlets Steel Scissor-style powder-coated base with dual crossbeams (1) Wheels (2) Foot Control STANDARD SPECIFICATIONS Height Range Powered 18”-35” (46-89 cm.) Length 73”... -
Page 7: Px150
PRODUCT DESCRIPTION PX150 Manual Lift-Assist Back Rest control Upholstered Top Self-locking molded rubber Accessory attachment feet (2) outlets Steel Scissor-style powder-coated base with dual crossbeams (1) Wheels (2) Foot Control STANDARD SPECIFICATIONS Motion 1 Powered 21”-38” (55-97 cm.) Height Range Length 73”... -
Page 8: Px300
PRODUCT DESCRIPTION PX300 Table Extender (accessory) Adjustable Arm Rests (2) (accessory) Manual Lift-Assist Back Rest control Upholstered Top Self-locking molded rubber feet (2) Steel Scissor-style Accessory attachment powder-coated base outlets with dual crossbeams (1) Wheels (2) Multi-function Foot Control STANDARD SPECIFICATIONS Motion 1 Powered 21”-38”... -
Page 9: Pt100
PRODUCT DESCRIPTION PT100 Upholstered Top Wheels (2) Single 24v motor with cover Foot Control Steel Scissor-style Optional Dual Self-locking powder-coated base Locking Casters molded rubber with dual crossbeams (1) feet (2) STANDARD SPECIFICATIONS Height Range Powered 16”-34” (40-86 cm.) Foot Control Height Motion Table Voltage Options 120V/60Hz or 230V/50Hz Table Capacity... -
Page 10: Pt150
PRODUCT DESCRIPTION PT150 Manual Lift-Assist Back Rest control Upholstered Top Seat section with Integrated Face Rest Steel Scissor-style powder-coated base with dual crossbeams (1) Single 24v Motor with cover Self-locking molded rubber feet (2) Wheels (2) Foot Control STANDARD SPECIFICATIONS Optional Dual Locking Casters Motion 1... -
Page 11: Pt200
PRODUCT DESCRIPTION PT200 Upholstered Top Articulating Head Rest Section with Adjustable Face Rest Cushion & Insert Pad Single 24v Motor with cover Manual Control for Back Rest Top Wheels (2) Self-locking Foot Control molded rubber Steel Scissor-style feet (2) powder-coated base with dual crossbeams (1) Optional Dual Locking Casters... -
Page 12: Pt250
PRODUCT DESCRIPTION PT250 Upholstered Top Articulating Head Rest Section Self-locking molded rubber feet (2) Manual Control for Steel Scissor-style Articulating Head Rest powder-coated Section base with dual crossbeams (1) Single 24v motor Foot Control with cover Wheels (2) Optional Dual Locking Casters STANDARD SPECIFICATIONS Motion 1... -
Page 13: Pt300
PRODUCT DESCRIPTION PT300 Manual Lift-Assist Back Rest control Articulating Head Rest Section Optional Dual Locking Casters Steel Scissor-style powder-coated base with dual Foot Control crossbeams (1) Single 24v Manual Control for motor with cover Articulating Head Rest Wheels (2) Section STANDARD SPECIFICATIONS Motion 1 Powered 16”-34”... -
Page 14: Pt400
PRODUCT DESCRIPTION PT400 Electrically Controlled Center Break Manual Lift-Assist Back Rest control Articulating Head 24v motor Rest Section Optional Dual Locking Casters Steel Scissor-style powder-coated base with dual Foot Control crossbeams (1) Single 24v motor with cover Manual Control for Wheels (2) Articulating Head Rest Section... -
Page 15: Pt400M
PRODUCT DESCRIPTION PT400M Electrically Controlled Center Break Self-locking 29.5” molded rubber (75 cm.) feet (2) 11” QuickLock Plat- (29 cm.) form & Boiance Face Pad Steel Scissor-style powder-coated base with dual crossbeams (1) 21.5” (55 cm.) Wheels (2) Foot Control 22”... -
Page 16: Orthopedic Hi-Lo Casting Table
PRODUCT DESCRIPTION Orthopedic Hi-Lo Casting Table Upholstered Top Gas Assist Control for Backrest Retractable side rail Self-locking Resin casting molded rubber cover feet (2) Manual Control for Articulating Casting Section Single 24v motor Optional Dual with cover Locking Casters Steel Scissor-style powder-coated base with dual crossbeams (1) Foot Control... -
Page 17: Installation
INSTALLATION The Tables come completely assembled and ready to use. Plug the cord into a functioning outlet that is rated for the table. (see Grounding below) Arrange the power cord and control cords so that they will not create a tripping hazard and where the controls are located to your liking and are conveniently accessible. -
Page 18: Directions For Use
DIRECTIONS FOR USE CONTROL OPERATIONS - ALL TABLES EXCEPT PX300, PT400 & PT400M) Be sure the self-locking molded rubber feet are flat side down to ensure safety and stability. CAUTION The tables offer height positioning with electronic ease. Operate the Foot control and Optional Hand Control as shown below to raise or lower the height of the table. - Page 19 DIRECTIONS FOR USE FOOT CONTROL OPERATIONS - PT400 & PT400M TABLES ONLY DO NOT sit or stand on the articulating head rest section. Be sure the self-locking molded CAUTION rubber feet are flat side down to ensure safety and stability. The O PT400 and PT400M tables offer height and center break positioning with electronic ease.
- Page 20 DIRECTIONS FOR USE HAND CONTROL OPERATIONS - PT400 & PT400M TABLES ONLY DO NOT sit or stand on the articulating head rest section. Be sure the self-locking molded CAUTION rubber feet are flat side down to ensure safety and stability. The O PT400 and PT400M tables offer height and center break positioning with electronic ease.
-
Page 21: Px300
DIRECTIONS FOR USE FOOT CONTROL OPERATIONS - PX300 TABLES ONLY CAUTION Do not sit backrest ot leg rest sections. Be sure the self-locking molded rubber feet are flat side down to ensure safety and stability. The hood area under the backrest top is not designed for storage. DO NOT use this area for holding anything. - Page 22 DIRECTIONS FOR USE HAND CONTROL OPERATIONS - PX300 TABLES ONLY CAUTION Do not sit backrest ot leg rest sections. Be sure the self-locking molded rubber feet are flat side down to ensure safety and stability. The hood area under the backrest top is not designed for storage. Do not use this area for holding anything.
-
Page 23: Adjusting The Back Rest
PT400 video. Watch the video! Dr. Robert DuVall, PT, DHSc, ATC, OCS, SCS, FAAOMPT CSCS At the Oakworks® factory in PA reviewing the Oakworks® PT400. Side bend to elongate the quadratus lumborum Posterior pelvic tilt... -
Page 24: Articulating Head Rest Use
DIRECTIONS FOR USE ARTICULATING HEAD REST USE Do not sit or stand on the articulating head rest section. Do not use Head Rest Section in CAUTION assisting the client on or off the table. Grasp Firmly & Lift Release Knob TO RAISE THE HEAD REST TO LOWER THE HEAD REST: Grasp the edge of the section and lift up until you... -
Page 25: Pt400M - Rotating Arm Rests Use
DIRECTIONS FOR USE PT400M - ROTATING ARM RESTS USE Be sure to install the arm rest on the Screw the Arm Rests into the pre- Adjust the Arm Rests as needed for correct side of the table. The arm rest drilled hole on the under side of each support and patient access. -
Page 26: Moving The Table
DIRECTIONS FOR USE MOVING THE TABLE Before moving any of the Tables, disconnect the power cord from the power outlet. The CAUTION table weighs as much as 200 lbs. (91 kg.) Use extreme caution when lifting the table to move it. Two people are required to move the table safely. DO NOT use the table to transport a patient. -
Page 27: Quicklock Face Rest Use
DIRECTIONS FOR USE TABLE EXTENDER USE CAUTION Do not put excessive weight or pressure on the table extender. The Table Extender lengthens the table for your tallest clients and can improve access to your patient. Accessory attachment outlets Locate the Accessory attach- Insert the Table Extender ment outlets. -
Page 28: Adjustable Arm Rest Installation And Adjustment
DIRECTIONS FOR USE ADJUSTABLE ARM REST INSTALLATION AND ADJUSTMENT Do not use the arm rest for patient support during the mounting or dismounting of the chair. CAUTION The arm rest is not designed to support the patient’s weight. TO INSTALL THE ARM RESTS: The Arm Rests adjust automatically as the back rest moves to remain parallel to the floor. -
Page 29: Cleaning & Disinfection
To reduce the risk of electric shock: DANGER - Always unplug this furnishing from the electrical outlet before cleaning. The following cleaners were tested by OAKWORKS ® and found to be acceptably compatible with all materials used in construction of our tables: Formula 409 ®... -
Page 30: Cleaning Process
- Always unplug this furnishing form the electrical outlet before cleaning. ® Follow the cleaners/disinfectant manufacturers’ directions for use. Please note that cleaning and disinfecting an OAKWORKS table is a two part process. First it must be cleaned of any visible soil, then it can be disinfected. The table should be cleaned as soon as possible after use. -
Page 31: Model Number & Serial Number
FM = Firm Table Top Length Minimum Table Height Table Top Width Top: FT = Flat BR = Lift-Assist Backrest LS = Lift Assist Salon ES = Electric Salon Base: EX = Medical Table Table Model: PX = PX Series... -
Page 32: Pt Series
MODEL NUMBER & SERIAL NUMBER PT SERIES Model Number Serial Number Model Numbers and Serial Numbers always start with a letter. 16796025 PXSLA3311873ACTTVN Ser#: PXR563146 US G2 30 x 22-38 x 72 3M/TT/2S TTSKYBLUE 01/04/2013 Order#:654321 Notes: Sample Product Label The model number and serial number are located on the underside of the foot section. -
Page 33: Specifications
SPECIFICATIONS PRODUCT SPECIFICATIONS Table Weights: 151-202 lbs. (68-92 kg.) Shipping Weights: 236-287 lbs. (107-130 kg.) Lifting Capacity 550 lbs. (250 kg.) ENVIRONMENTAL CONDITIONS Conditions Temperature Humidity Atmospheric Pressure Normal Use 50° (10°C) to 104° (40°C) 20% to 60% RH 98 to 105 kPa Storage &... -
Page 34: Guidance And Manufacturer's Declaration - Electromagnetic Emissions
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic emissions The table is intended for use in the electromagnetic environment specified below. The customer or the user of the table should assure that it is used in such an environment. Emissions Test Compliance Electromagnetic environment - guidance The table uses RF energy only for its internal... -
Page 35: Guidance And Manufacturer's Declaration - Electromagnetic Immunity
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic immunity The table is intended for use in the electromagnetic environment specified below. The customer or the user of the table should assure that it is used in such an environment. Electromagnetic Immunity Test IEC 60601 test level Compliance level environment - guidance... -
Page 36: Electromagnetic Immunity
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic immunity The table is intended for use in the electromagnetic environment specified below. The customer or the user of the table should assure that it is used in such an environment. Electromagnetic Immunity Test IEC 60601 test level Compliance level environment - guidance... - Page 37 THIS PAGE IS INTENTIONALLY LEFT BLANK...
- Page 38 THIS PAGE IS INTENTIONALLY LEFT BLANK...
- Page 39 THIS PAGE IS INTENTIONALLY LEFT BLANK...
-
Page 40: Contact Information
USER MANUAL OAKWORKS ® PX & PT Tables CONTACT INFORMATION: Inc. ® AKWORKS 923 East Wellspring Road New Freedom, PA 17349 Phone: 717-235-6807 FAX: 717-235-6798 www.oakworksmed.com 3034177 CONFORMS TO: ANSI/AAMI STD ES60601-1 IEC STD 60601-1 3RD EDITION IEC STD 60601-1-2 3RD EDITION IEC STD 60601-1-6 3RD EDITION CERTIFIED TO CAN/CSA STD C22.2 NO.
Need help?
Do you have a question about the PX Series and is the answer not in the manual?
Questions and answers