Global - Dexibell VIVO S9 Owner's Manual

Parameter Setting
1 ~ 16
Channel
default: 15
3.
If you selected the "Organ Control" part, the following page is showed:
Parameter Setting
OFF, ON
Status
Default: On
1 ~ 16
Channel
default: 14
4.
If you selected the "Common" part, the following page is showed:
Parameter Setting
OFF, ON
Active Sensing
(FEH)
Default: On
 MIDI SET
MIDI Sets are memories for MIDI settings. The S9 provides five MIDI
Set memories.
The first MIDI Set, called "Dexibell", is read-only and allows you to
restore the MIDI factory setting.
The second MIDI Set called "KeyboardZone", it is read-only and
is a fast way to configure the MIDI channels using the zones. See
"Master Keyboard Zone" (p. 54).
The third MIDI Set called "Pedalboard", it is read-only. It's a quick
way to configure the MIDI channels using an external Pedalboard.
The keyboard pedal part is set Local Off. In other words, the internal
connection between the keyboard part and the tone generator is
interrupted.
The other three memories (User 1, User 2, User 3) allow use to
memorize and recall your MIDI configuration.
70
Memory
Explanation
Allows you to assign a MIDI transmit
channel to the "Memory" part.
Memory
Explanation
Select "On" if you want transmit position
MIDI messages of the draw-faders. For
details regarding the MIDI messages
transmitted, see "Draw-faders MIDI
Controls" (p. 76).
Allows you to assign a MIDI transmit
channel to the "Organ control" part.
Common
Explanation
This MIDI message is transmitted
constantly at intervals of approximately
250 ms.
This MIDI message is used to monitor
the MIDI connection. If there was a
disconnection, after a connection has
been made, the connected device no
longer receives the active sensing (FEH)
message and reset all notes that have
remained actives.
Select "On" if you want to transmit the
Active Sensing MIDI.
MENU Options (Advanced Section)
1.
Use the [DATA ENTRY] knob or the [][] to select the MIDI Set and press
the "RECALL" Function button to load it.
2.
Press the "SAVE" Function button to jump in the SAVE MIDI SET page.
 SAVE MIDI SET
1.
Use the [DATA ENTRY] knob or the [][] to select the MIDI Set memory
and press the "WRITE" Function button to save your configuration.

GLOBAL

[MENU] button GLOBAL
This parameter is automatically saved in the S9 global memory area.
Parameter Setting
Off, 5 min, 10 min,
30 min, 2 hours, 4
Auto OFF
hours
Default: 2 hours
Global, Memory
Switch
Default: Memory
Global, Memory
Pedal
Default: Memory
Off, On
Motor Slider
Default: On
GLOBAL MEMORY
Explanation
This parameter allows you to cause the S9 to
switch itself off after the selected number of
minutes has elapsed if you are not using it.
Select "Off" if you prefer not to use this
function.
Global: Set this value if you want the switch
assignments are saved in the global area. The
switch assignment does not depend on the
recalled memory.
Memory: Set this value if you want the switch
assignments are saved in the Memories. The
switch assignment depends on the recalled
memory.
For the switch assignements, see "ASSIGN 1, 2
SWITCH" (p. 65).
Global: Set this value if you want the pedal
assignments are saved in the global area. The
pedal assignment does not depend on the
recalled memory.
Memory: Set this value if you want the pedal
assignments are saved in the Memories. The
pedal assignment depends on the recalled
memory.
For the pedal assignements, see p. 64.
On: Set this value if you want the draw faders
motorised.
Off: Set this value if you do not want the draw
faders motorised.