Danfoss VLT 5000 Series Design Manual page 43

Compact, Mains supply 3 x 380 - 500 V
According to international requirements
Normal overload torque (110 %):
Output current
Output
Typical shaft output
Typical shaft output
High overload torque (160 %):
Output current
Output
Typical shaft output
Typical shaft output
Max. cable cross-section to motor,
brake and loadsharing [mm
Min. cable cross-section to motor,
brake and loadsharing [mm2]/[AWG]
Rated input current
Max. cable cross-section,
power [mm
Max. pre-fuses
Efficiency
Weight IP 20 EB
Weight IP 54
Power loss at max. load.
- high overload torque (160 %)
- normal overload torque (110 %)
Enclosure
1. For type of fuse see section Fuses.
2. American Wire Gauge.
3. Measured using 30 m screened motor cables at rated load and rated frequency.
4. Min. cable cross-section is the smallest cable cross-section allowed to be fitted on the terminals to comply with IP 20. Always comply
with national and local regulations on min. cable cross-section.
42
I
VLT, MAX
I
VLT, MAX
I
VLT, MAX
I
VLT, MAX
2 2)
]/[AWG]
2) 4)
2
]/[AWG]
3)
®
VLT 5000 Design Guide
VLT type
I [A] (380-415 V)
VLT,N
(60 s) [A] (380-415 V)
I [A] (440-500 V)
VLT,N
(60 s) [A] (440-500 V)
S [kVA] (380-415 V)
VLT,N
S [kVA] (440-500 V)
VLT,N
P [kW]
VLT,N
P [HP]
VLT,N
I [A] (380-415 V)
VLT,N
(60 s) [A] (380-415 V)
I [A] (440-500 V)
VLT,N
(60 s) [A] (440-500 V)
S [kVA] (380-415 V)
VLT,N
S [kVA] (440-500 V)
VLT,N
P [kW]
VLT,N
P [HP]
VLT,N
IP 54
IP 20
I [A] (380 V)
L,N
I [A] (460 V)
L,N
IP 54
IP 20
1)
[-]/UL [A]
[kg]
[kg]
[W]
[W]
®
MG.52.B2.02 - VLT is a registered Danfoss trademark
5016 5022 5027
32 37.5 44
35.2 41.3 48.4
27.9 34 41.4
30.7 37.4 45.5
24.4 28.6 33.5
24.2 29.4 35.8
15 18.5 22
20 25 30
24 32 37.5
38.4 51.2 60
21.7 27.9 34
34.7 44.6 54.4
18.3 24.4 28.6
18.8 24.2 29.4
11 15 18.5
15 20 25
16/6 16/6 16/6
16/6 16/6 35/2
10/8 10/8 10/8
32 37.5 44
27.6 34 41
16/6 16/6 16/6
16/6 16/6 35/2
63/40 63/50 63/60
0.96 0.96 0.96
21 22 27
41 41 42
419 559 655
559 655 768
IP 20/ IP 20/ IP 20/
IP 54 IP 54 IP 54