Table of Contents
Advertisement
Infinity/Infinity HD specifications
Specification type
Load capacity
Rated speed
Maximum travel
Maximum # of stops
Pit depth required
Minimum overhead clearance
Power supply (circuit to be supplied by others)
NOTE: Amperage may vary depending on
individual units. Verify requirements prior to
installation of power supply.
Lighting supply (circuit to be supplied by
others)
Motor
Drive system
Control system
Noise level (for typical installation)
Daily cycle
Cab size
Cab panel finish
Hall call station and control panel finish
Standard features
Options
Part No. 000783, 24-m09-2015
Specification data
Infinity: 750 lb (341 kg), 950 lb (431 kg) or 1000 lb (454 kg)
Infinity HD: 1400 lb (635 kg)
36 ft/min (0.18 m/s) nominal
50 ft (15.24 m) – confirm with local code
6 stops
Infinity: 8" (203 mm) minimum up to 96" (2438 mm)
Infinity HD: 12" (305 mm) minimum up to 96" (2438 mm)
92" (2337 mm) for standard 80" cab; 96" (2438 mm) for 84" cab, 108" (2743 mm) for 96" cab
North American: 208 volt, three-phase, 30 amps, 60 Hz or 230 volt, single-phase, 30 amps, 60 Hz
NOTE: 60 Amps for Infinity HD
International: 220 volt, single-phase, 40 amps, 50 Hz
North American: 115 volt, 60 Hz, 15 amps
International: 220 volt, 50 Hz 15 amps
Infinity: 3 HP (2.24 kW)
Infinity HD: 5 HP (3.73 kW)
1:2 cable hydraulic
Automatic user interface
Solid state electronics with relay logic motor controls
74.0 dBA; measured at a height of 1m, distance of 1m, in front of tank, in closed machine room
Normal: 30
Heavy: 75
Excessive: 100
Maximum starts in 1 hour on standard installation: 15
NOTE: Please consult your Sales Representative if there a chance you may exceed these amounts.
Infinity Type 1L, 1R, 2, 3, 4, and 5:
• 36" x 48" (914 mm x 1219 mm)
• 36" x 54" (914 mm x 1372 mm)
• 36" x 60" (914 mm x 1524 mm)
• 40" x 54" (1016 mm x 1372 mm)
Infinity HD Type 1L, 1R, 2, 3, 4 and 5:
• 48" x 60" (1219 mm x 1524 mm)
Solid melamine or MDF panels (standard)
Unfinished veneer (optional)
Solid hardwood raised panels (optional)
Clear or bronze anodized aluminum (standard)
Stainless steel or brass (optional)
Rectangular (standard) or oval (optional) hall stations, keyless (standard) or keyed (optional)
Alpha-numeric button marking (optional)
Anti-creep device
Automatic cab on/off lighting
Cab gate safety switch
Car top stop switch
In car digital floor indicator
Clear or bronze anodized aluminum cab entrance trim and handrail
Data plates, capacity tags and rope tags
Emergency stop and alarm buttons
Emergency battery back-up for lighting, alarm and emergency lowering
Upper and lower terminal limits
Magnetic floor selection, stopping and re-levelling
Manual reset slack rope safety switch
Mechanical rail shoring blocks
Negative pressure switch
Pit switch
Pump run timer
Rail sections (8 ft optional or 16 ft standard)
Two 12 V, 4 AH, sealed no maintenance batteries with 24 V, 4 amp Smart Charge™ battery charge
Unfinished plywood sub-floor
Variable speed pressure compensated valve with manual lowering
White ceiling with recessed incandescent down lights
84" (2133 mm) or 96" (2438 mm) high cab
Automatic gate operator (accordion gates only)
Automatic swing door operator
Phone cabinet
Hose with flow control valve (15 ft, 20 ft or 25 ft)
Interlocks for doors by others
Keyed on/off control panel and hall stations
Light screens
Pipe rupture valve
Buffer springs (13" pit depth minimum)
Split cylinder for travel over 384" (9754 mm)
Auto slim doors
Infinity and Infinity HD Planning Guide
5
2-
Advertisement
Table of Contents
