Sony HXCU-FB80 4K/HD Operating Instructions Manual page 8

Pressing the CONTROL knob performs the same function as
setting the CANCEL/ENTER lever to the ENTER position.
e PANEL ACTIVE button
Activates the control panel to control the camera connected to
the CCU (panel active state). When the button is lit, the
IRIS/MB ACTIVE indicator also turns on simultaneously.
When the button is not lit, the panel is deactivated (panel lock
state) to prevent inadvertent operation.
f SW1, SW2 (assignable switch 1, 2) buttons
Controls the function assigned to each button on the <FRONT
PANEL 1> page in the CCU CONFIGURATION menu. The
button light turns on/off as the assigned function is switched
on/off.
For details, see "ASSIGNABLE/CUSTOM" (page 31) on
<FRONT PANEL 1>.
g BARS (color bars) button
Switches on the color bar signal output to the monitor
connected to the CCU (button light turns on). Pressing the
button again restores the previous signal output.
h STANDARD button
Stores the current camera settings as the reference file data
values in the camera (button light turns on for a few seconds).
While the button is lit, pressing the button again cancels the
operation and restores the previous data values.
i SHUTTER control block
Controls the shutter settings.
ON button
ECS (extended clear scan) button
Display
UP/DOWN lever
SHUTTER
ECS
UP
ON
DOWN
• ON button
Switches the normal shutter function, extended clear scan
function, or slow shutter function on/off (button light turns
on/off).
• ECS (extended clear scan) button
Switches the extended clear scan mode on/off (button light
turns on/off).
• Display
When the ECS button is lit: Displays the clear scan frequency.
When the ECS button is not lit: Displays the shutter speed.
The indicator is not displayed when auto shutter is on.
• UP/DOWN lever
When the ECS button is lit: Adjusts the clear scan frequency.
UP increases the frequency, and DOWN decreases the
frequency.
When the ECS button is not lit: Adjusts the shutter speed. UP
increases the shutter speed, and DOWN decreases the
shutter speed.
The number of frames at slow shutter speed increases when
the lever is in the UP position, and decreases in the DOWN
position.
Holding the lever UP or DOWN advances the setting in that
direction.
j MASTER GAIN control block
Controls the video output signal gain in response to the
lighting of the subject.
Display
UP/DOWN lever
MASTER GAIN
UP
DOWN
• Display
Displays the video output signal gain setting (dB units).
The indicator is not displayed when auto gain (AGC) is on.
• UP/DOWN lever
Adjusts the video output signal gain setting (dB units).
UP increases the gain, and DOWN decreases the gain.
Holding the lever UP or DOWN advances the setting in that
direction.
k ALARM indicator
Lights up red to indicate an error in the CCU or camera
system.
l OPTICAL CONDITION CAM/CCU (optical reception)
indicator
The CAM indicator shows the reception status of the
connected camera adaptor, and the CCU indicator shows the
reception status of the unit.
The reception level is good.
Green:
The reception level is low.
Orange:
The reception level is extremely low.
Red:
A transmission error has occurred.
Off:
m POWER switch
Switches the power for the entire system on and off, including
the CCU, camera, and the RCP-1000-series Remote Control
Panel connected to the REMOTE connector on the rear panel.
Pressing the "?" side turns the camera system on, and
pressing the "a" side turns it off.
n CAM POWER indicator
Turns on when power is supplied to the camera.
o LOCK switch
Locks the buttons on the front panel. Select the desired
buttons to be locked on the <FRONT PANEL 3> page in the
CCU CONFIGURATION menu.
For details, see "<FRONT PANEL 3>" (page 32).
p NETWORK indicator
Displays the network system connection status.
Indicates that external control equipment (RCP-1000-
On:
series Remote Control Panel or other device) is
connected.
Indicates a connection problem with the external
Flashing:
control equipment (RCP-1000-series Remote Control
Panel or other device).
Off: Indicates that a LAN cable is not connected or that the
network system connection parameters have not been set.
8