Table of Contents
Advertisement
Flare: Flare balance R/G/B value
DTL: Detail level
Note
The items are the same as those on “Page 1” (page 16) in the
“Camera settings” section.
System status
* S y s t e m S t a t u s
1 / 2*
H X C - F B 8 0
1 0 8 0 / 5 9 .9 4P
( O E T F : H L G _L IV E)
R e f e r e n c e : F r e e L o c k
S L O T 1 - 1 & 2 : 1 0 8 0 / 5 9 . 94 I
S L O T 1 - 3 & 4 : 1 0 8 0 / 5 9 . 94 I
S L O T 2 - 1 & 2 : 4 K / 5 9 . 9 5 P 2S I
( O E T F : H L G _L IV E)
S L O T 2 - 3 & 4 : 4 K / 5 9 . 9 5 P 2S I
( O E T F : S D R )
* S y s t e m S t a t u s
2 / 2*
H X C - F B 8 0
1 0 8 0 / 5 9 .9 4I
( O E T F : H L G _L IV E)
R e t u r n - 1 : S D I - 1 ( H D )
R e t u r n - 2 : S D I - 2 ( S D )
R e t u r n - 3 : V B S - 1
R e t u r n - 4 : F B S - 2
The camera model name, format, and camera OETF
(HLG_LIVE or SDR) are displayed at the top of the page when
a camera is connected to the unit. A “---” mark is displayed
when a camera is not connected.
Reference: Reference signal format and lock status
SLOT1-1&2: SLOT1 SDI OUTPUT 1/2 connector output
format selection
SLOT1-3&4: SLOT1 SDI OUTPUT 3/4 connector output
format selection
SLOT2-1&2: SLOT2 SDI OUTPUT 1/2 connector output
format selection and connected camera OETF (HLG_LIVE
or SDR) indicator
SLOT2-3&4: SLOT2 SDI OUTPUT 3/4 connector output
format selection and connected camera OETF (HLG_LIVE
or SDR) indicator
Return-1: Return channel setting of Return 1
Return-2: Return channel setting of Return 2
Return-3: Return channel setting of Return 3
Return-4: Return channel setting of Return 4
CCU hardware diagnostics
* D i a g n o s i s *
3/ 14
D P R
: O K
A T
: O K
F r o n t P a n e l : O K
The camera Auto Setup category, and the corresponding
setup item and status are displayed at the top of the page.
DPR: DPR board status
AT: AT board status
Front Panel: Front panel status
Camera system diagnostics
Page 1
*S y s t em D i ag 1 / 3*
4/ 1 4
Op t i c al C o nd i t i on
C A M E RA
O K
C C U
O K
F a n Po w e r O K
T i m e r
0 H
C C U Po w e r O K
Se r i a lN o 0 00 0 0 0 00
CAMERA: Camera light sensor status
CCU: CCU light sensor status
Fan Power: CCU power supply fan status
Timer: Elapsed time since power-on
CCU Power: CCU power supply status
SerialNo: CCU serial number
Page 2
*S y s t em D i ag 2 / 3*
5/ 1 4
C A M ER A
Ca b l e C o n n ec t
Da t a
O K
Po w e r O K
R E M OT E
Ca b l e C o n n ec t
Da t a
O K
Po w e r O K
ssxxxxxxb
C A M:
G re e n
ssxxxxxxb
CC U:
G re e n
CAMERA Cable: Camera cable connection status
CAMERA Data: Camera data transmission status
CAMERA Power: Camera power supply status
REMOTE Cable: Remote device cable connection status
REMOTE Data: Remote device data transmission status
REMOTE Power: Remote device power supply status
CAM/CCU (light sensor level indicator): CAM displays
camera light sensor level, and CCU displays CCU light
sensor level.
Page 3
*S y s t em D i ag 3 / 3*
6/ 1 4
I n t e rc o m
C C U F R O NT
E NG
P GM O N
C A ME R A
E NG
M IC O N
C A M MI C G ai n
C H 1( F R O NT ) 6 0dB
C H 2( R E A R)
6 0dB
S U B CM D
- -- - - - --
Intercom CCU FRONT: CCU intercom selection
Intercom CAMERA: Camera intercom channel selection and
microphone status
CAM MIC Gain CH1 (FRONT): Amplifier gain for a
microphone connected to the camera AUDIO 1 IN
connector.
Page 17
Hide quick links:
Advertisement
Table of Contents
