Rear Panel - Sony HXCU-FB80 4K/HD Operating Instructions Manual

Rear Panel

a "Memory Stick" slot
For service use only.
b
LAN jack (RJ-45, 8-pin)
Connects to a LAN hub (10BASE-T/100BASE-TX), when
using a network connection, via a LAN cable (shielded type,
category 5 or higher).
CAUTION
For safety, do not connect the connector for peripheral device wiring
that might have excessive voltage to this port.
Follow the instructions for this port.
c HD PROMPTER (HD teleprompter connectors) (BNC
type)
When a camera that supports an HD teleprompter function is
connected to the CAMERA connector, the HD-SDI signal input
on this connector is output from the SDI I/O connector of the
camera.
Note
Input an HD-SDI signal having frequency synchronization with the
camera control unit.
d SLOT2, SDI OUTPUT 1 to 4 (4K/3G/HD TRUNK output)
connectors (BNC type)
Outputs the camera signal as 12G SDI signal, 3G SDI signal,
or 1.5G signal (HD TRUNK only).
e RETURN INPUT SDI1, SDI2, VBS1, VBS2 (VBS/SDI
return video) connectors (BNC type)
Inputs the VBS return video signals (2-system), HD SDI or SD
SDI return video signals (2-system).
f AUDIO OUTPUT CH-1, CH-2 connectors (XLR 3-pin)
Outputs audio signals from the camera AUDIO 1 IN and
AUDIO 2 IN connectors.
g CAMERA connector (optical fiber connector)
Connect to the target camera or CA-FB70 HD Camera
Adaptor.
When you use an optical composite cable for connection,
power supply, all camera signals, such as control signal, video
signal and audio signals can be transmitted.
When you use only single-mode optical fiber cables for
connection, all signals (except power supply) can be
transmitted by a pair of single-mode optical fiber cables.
For details about pin assignment, see "CAMERA connector"
(page 37).
Note
If the terminations of the single-mode optical fiber cable or optical
composite cable are contaminated with dust, etc., transmission errors
may occur. Be sure to replace the cap that came with the cable over
the termination when a cable is not in use.
h AC supply input connector
Connects to the AC supply via the specified power cord
(optional). A plug holder (optional) can be used to secure the
power cord to the CCU.
i REFERENCE (reference input) connectors (BNC type)
Inputs an HD tri-level reference sync signal or SD
IN:
reference sync signal (black burst signal) for external sync.
OUT: The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75 Ω terminator.
j PROMPTER (teleprompter input) connectors (BNC
type)
Inputs the VBS signal for the teleprompter.
IN:
The input signal is output from the other connector as-is
OUT:
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75 Ω terminator.
k REMOTE connector (8-pin)
Transmits and receives control signals from the RCP-1000-
series Remote Control Panel via a CCA-5 cable (optional). It
also supplies power when connected to an RCP-1000-series
Remote Control Panel.
l VBS 1, 2 (composite video signal 1, 2) connectors
(BNC type)
Outputs (2-system) the camera signals in composite signal
format.
m SLOT1, SDI OUTPUT 1 to 4 connectors (BNC type)
Outputs the camera signals in HD SDI or SD SDI signal
format.
The SDI OUTPUT 3 and SDI OUTPUT 4 connectors can also
output signals with superimposed character or marker display.
n PIX (picture monitor output) connector (BNC type)
Outputs a video signal for a picture monitor. It can also output
a signal with superimposed character display.
o SYNC (sync signal output) connector
Outputs a sync signal for connection to the sync signal input
connector of a waveform monitor or picture monitor.
10