Subscribe to Our Youtube Channel
Related Manuals for Extron electronics XTP T FB 202 4K
Summary of Contents for Extron electronics XTP T FB 202 4K
- Page 1 User Guide XTP Systems XTP T FB 202 4K Two-input Universal Floor Box Twisted Pair Transmitter 68-2832-01 Rev. A 05 19...
- Page 2 Safety Instructions Safety Instructions • English Istruzioni di sicurezza • Italiano AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire WARNING This symbol, , when used on the product, is intended to l’utente della presenza di tensione non isolata pericolosa all’interno del alert the user of the presence of uninsulated dangerous voltage within the contenitore del prodotto che può...
- Page 3 ついては、 エクス トロンのウェブサイ ト より 『Extron Safety www.extron.com and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください。 Copyright © 2019 Extron Electronics. All rights reserved. www.extron.com Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ( ®...
- Page 4 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 5 Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessure mineure. ATTENTION: •...
-
Page 6: Table Of Contents
RS-232 and IR Over XTP Communication ..16 Menu Bar ............29 Power Connection ......... 17 Device Settings ..........32 Operation ..........20 Switch Modes ........... 20 EDID ..............20 Reset Mode ............20 XTP T FB 202 4K Floor Box Transmitter • Contents... - Page 7 XTP T FB 202 4K Floor Box Transmitter • Contents...
-
Page 8: Introduction
This guide contains installation and control procedures, as well as reference information for the XTP T FB 202 4K Universal Floor Box Twisted Pair Transmitter. In this guide, the terms “XTP T FB 202 4K” and “transmitter” are used interchangeably to refer to the XTP T FB 202 4K Universal Floor Box Twisted Pair Transmitter. -
Page 9: System Compatibility
Typical XTP T FB 202 4K Application System Compatibility The XTP T FB 202 4K is compatible with XTP systems, but the maximum video resolution may be limited with different XTP devices. See the table below for maximum video resolutions and refresh rates for various XTP systems. -
Page 10: Key Features
Ethernet pass-through port to reduce the amount of independent network drops required within a system. • Remote power capability — Allows the XTP T FB 202 4K to be powered by an XTP CrossPoint Matrix Switcher or XTP Power Injectors to simplify integration. •... -
Page 11: Installation
Installation This section contains information for installing, connecting, and wiring the XTP T FB 202 4K. Topics in this section include: • Installation Overview Adapter Plates • • Side Panel Connectors • Top Panel Features • Mounting • Connection and Wiring Details... -
Page 12: Adapter Plates
NOTE: The 995242 adapter plate is only used for position 2 of the Ackermann GB3 (OBO Bettermann) floor box. Determine the position in the floor box to install the XTP T FB 202 4K. Each compatible floor box contains three positions to install devices (see figure 2). - Page 13 Installing 995243 Adapter Plates Rotate the adapter plate down so the bottom flange rests against the wall of the floor box. Figure 5. Fixing the Adapter Plate (995241 Shown) in Place XTP T FB 202 4K Floor Box Transmitter • Installation...
-
Page 14: Side Panel Connectors
Wire the connector as shown in figure 8. REMOTE RS-232 G Rx Tx Do not tin the wires! Controlling Device Bidirectional Transmit (Tx) Transmit(Tx) Receive (Rx) Receive (Rx) Ground (G) Ground(G) Figure 8. RS-232 Wiring XTP T FB 202 4K Floor Box Transmitter • Installation... - Page 15 For wiring considerations, see Power Connection on page 17. Remote power NOTE: The XTP T FB 202 4K can also be powered remotely (see on page 19). XTP T FB 202 4K Floor Box Transmitter • Installation...
-
Page 16: Connectors Above The Adapter Plates
(see page 10) RS-232 and IR Over XTP connector Configuration port (see page 10) (see page 10) LED indicators (see page 10) LAN connector (see page 10) Figure 10. Top Panel Features XTP T FB 202 4K Floor Box Transmitter • Installation... - Page 17 • Clip LED indicator — Lights when the analog audio input signal remains above • -3 dBFS. It remains lit for 200 ms after the signal falls below -3 dBFS. XTP T FB 202 4K Floor Box Transmitter • Installation...
-
Page 18: Mounting
(see Adapter Plates on page 5). Align the screw holes on the XTP T FB 202 4K with the screw holes on the adapter plates. Using the provided self-threading screws and washers, secure the XTP T FB 202 4K to the adapter plates (see figures 12 though 15). -
Page 19: Mk Electric Cablelink Plus Modular Floor Box
M OT -2 32 Extron XTP T FB 202 4K (shown in Electraplan floorbox assembly) Figure 15. Mounting the XTP T FB 202 4K into an Electraplan or PUK Floor Box XTP T FB 202 4K Floor Box Transmitter • Installation... -
Page 20: Connection And Wiring Details
ATTENTION: • Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP T FB 202 4K Floor Box Transmitter • Installation... -
Page 21: Tp Cable Termination And Recommendations
Connector Figure 17. TP Cable Termination Supported cables The XTP T FB 202 4K is compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cables. ATTENTION: • Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the XTP products. - Page 22 • Loosely place cables and limit the use of tie wraps or hook and loop fasteners. • Separate twisted pair cables from AC power cables. XTP T FB 202 4K Floor Box Transmitter • Installation...
-
Page 23: Rs-232 And Ir Over Xtp Communication
Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws. • S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives. XTP T FB 202 4K Floor Box Transmitter • Installation... -
Page 24: Power Connection
Output Cord Figure 19. Power Wiring The XTP T FB 202 4K can be connected to a local power supply. See the notifications on the next page for local power considerations. XTP T FB 202 4K Floor Box Transmitter • Installation... - Page 25 La longueur idéale est de 5 mm (3/16 inch). TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out. XTP T FB 202 4K Floor Box Transmitter • Installation...
- Page 26 Remote power The XTP T FB 202 4K can be powered remotely through an XTP Power Injector or through an XTP matrix switcher. ATTENTION: • XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors.
-
Page 27: Operation
• Switch Modes The XTP T FB 202 4K has two switch modes: normal and auto switch. In normal mode, inputs must be selected manually. In auto switch mode (default), the XTP T FB 202 4K prioritizes a specified input depending on availability. These modes must be enabled or... -
Page 28: Sis Configuration And Control
Use a computer running the Extron DataViewer utility, or a control system to enable serial control of the switcher. To connect directly to an XTP T FB 202 4K, connect the computer to the XTP T FB 202 4K through the top panel USB configuration port (see... -
Page 29: Error Responses
Error Responses When the XTP T FB 202 4K receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the switcher returns an error response to the host. -
Page 30: Command And Response Tables For Sis Commands
= default) X& = Audio level = 720p @ 50 Hz = Black video signal resolution = 720p @ 60 Hz (default) = 1080p @ 60 Hz XTP T FB 202 4K Floor Box Transmitter • SIS Configuration and Control... -
Page 31: Picture Adjustment Commands (Analog Only)
KEY: = off or disable = Enable or disable = on or enable (default) 0-255 = Pixel phase = default) 0-65535 32768 = Horizontal or vertical shift XTP T FB 202 4K Floor Box Transmitter • SIS Configuration and Control... -
Page 32: Presets Commands
= Video or TMDS detected = HDCP authorization off = HDCP authorization = HDCP authorization on (default) = No source = HDCP status = HDCP compliant source = non-HDCP compliant source XTP T FB 202 4K Floor Box Transmitter • SIS Configuration and Control... -
Page 33: Xtp System Configuration Software
Configuration Software This section contains installation and configuration procedures for the XTP System Configuration Software for configuring and controlling the XTP T FB 202 4K. It can also be controlled with SIS commands (see SIS Configuration and Control on page 21). Topics... -
Page 34: Software Product Page
Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software... -
Page 35: Software Operation
Software Operation The XTP T FB 202 4K can be controlled directly from the top panel configuration port (see figure on page 9) or remotely from an XTP matrix switcher. Connections The XTP System Configuration Software opens to the screen. This screen is Connections used to establish communication with an XTP device through USB connection. -
Page 36: Menu Bar
Backup and Restore Commissioning Report available when directly connected to the XTP T FB 202 4K. See an XTP matrix switcher user guide (www.extron.com) for more information on these features. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software... - Page 37 From the menu, select . The Tools Software Preference Software Preference dialog box opens. Figure 30. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 38 This option opens the XTP System Configuration Software help file in a Web browser. From the menu, select Help Help Extron Website This option opens the Extron website in a Web browser. From the menu, select Help Extron Website XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
-
Page 39: Device Settings
NOTE: The signal indicators on the AV input buttons display green when a signal is present on the corresponding input or gray when there is no signal present. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software... - Page 40 HDCP authorized device. If the box is not checked, the source is blocked from encrypting its output. This may result in some content not being passed by the source device. NOTE: HDCP authorization is for the HDMI input only. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 41 Save Preset — To save a preset, select one from the list of presets and click the Save button. Preset Recall Preset — To recall a saved preset, select the desired preset from the list of presets and click the button. Recall Preset XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 42 If selected, also select the black signal resolution from the drop-down list. Signal Type The default resolution is 720p @ 60 Hz. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 43 Factory Reset settings except for firmware. NOTE: This is the same as the SIS command (see the Reset mode ZXXX command on page 25). XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 44 Audio Only — Displays whether the black video signal for audio-only transmission is enabled. Analog Audio Gain — Displays the analog audio gain in dB. XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 45 To assign EDID to all inputs: Select an available EDID icon from the , or Favorites Connected Outputs Available panel ( EDID Click the button ( Assign to All XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 46 Common Timings Connected Outputs listing the EDID settings common among the selected outputs. Select the desired common EDID. The EDID is shown in the panel. Available EDID XTP T FB 202 4K Floor Box Transmitter • XTP System Configuration Software...
- Page 47 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Need help?
Do you have a question about the XTP T FB 202 4K and is the answer not in the manual?
Questions and answers