2Jam Codes (Related To Finisher); 3Jam Codes (Related To Adf); 4Jam Codes (Related To Duplex Unit); 5Jam Codes (Related To Inner 2-Way Tray) - Canon iR2020 Series Portable Manual

Code
1118
3.2.2 Jam Codes (Related to Finisher)
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Code
0130
0231
0033
0035
1036
1137
3.2.3 Jam Codes (Related to ADF)
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Code
0000
0007
0008
0009
000a
000c
000d
000e
000f
0010
3.2.4 Jam Codes (Related to Duplex Unit)
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
0120
0124
0221
0228
3.2.5 Jam Codes (Related to Inner 2-way Tray)
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Code
010e
Name Sensor No.
Door open jam SR202,
SR203,
SR209,
SW2, SW3
Name Sensor No.
Delayed feed jam PI5
Staying paper jam PI5
Stack ejection jam PI1
Staple jam Stapler HP
sensor
(built in
stapler)
Power-on jam PI5
Door open jam SW1
Name Sensor No.
Unknown jam -
Initial stationary PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial
Read sensor delay PI7,PI8
Read sensor stationary PI7
Paper absence (Pull out PI11
the document.)
Delivery reversal sensor PI6,PI7
delay
Delivery reversal sensor PI6
stationary
ADF cover open PI10
User ADF open sensor of
the reader
unit
Pickup NG -
Code Name Sensor No.
Delay jam at duplex SR1002
paper sensor 1
Delay jam at duplex SR1003
paper sensor 2
Stationary jam at SR1002
duplex paper sensor 1
Stationary jam at SR1003
duplex paper sensor 2
Name Sensor No.
Delay jam at No.2 SR1101
delivery section
Description
The door was opened when there was printing paper in the transport
path.
T-3-3
Description
The inlet sensor is not turned on within the specified time after
reception of a paper ejection signal from the host machine.
The inlet sensor is not turned off even if paper is fed by the specified
distance after the leading edge of the paper from the host machine
has passed through the sensor.
When a paper stack is ejected, the HP sensor is not turned off within
the specified time.
The stapler HP sensor was turned off once after start of stapler
operation, but the HP has not been reached within the specified
time.
The inlet sensor detected paper at power-on.
The front cover switch detected opening of the front cover during
standby or copy operation.
T-3-4
Description
Other errors
operation.
The read sensor does not detect paper when the paper has been fed
by the predetermined distance since reception of a pickup request.
The trailing edge of paper is not detected when the paper has been
fed by the predetermined distance since detection of it by the read
sensor.
The Document set sensor has been held off since start of pickup.
The delivery reversal sensor does not detect paper since the paper
has been fed by the predetermined distance since the read sensor
was turned on.
The trailing edge of paper is not detected when the paper has been
fed by the predetermined distance since the delivery reversal sensor
detected the paper.
The feeder cover was opened during operation (of the drive system).
The ADF was opened during operation (of the drive system).
The registration sensor has been held off since paper pickup started.
T-3-5
Description
The duplex paper sensor 1 does not turn on within the specified
time after the delivery sensor on the main unit side turns on.
The duplex paper sensor 2 does not turn on within the specified
time after the duplex reverse motor starts.
- The duplex paper sensor 1 does not turn off when the specified
time has lapsed since the duplex paper sensor 2 turned on.
- The duplex paper sensor 1 does not turn off when the paper
with a longitudinal length of 280 mm reaches the standby
position (about 90 mm from the duplex paper sensor 2).
The duplex paper sensor 2 does not turn off when the specified
time has lapsed since the feed motor started.
T-3-6
Description
The No.2 delivery sensor does not detect presence of paper within
the specified time after turning on of the fixing delivery sensor.
Chapter 3
0011-2849
0011-2839
0011-2840
0011-2850
7