Jam Code; 1Jam Codes (Related To Printer Unit) - Canon iR2020 Series Portable Manual

Chapter 3
E719
E733
E736
E739
E805
E808

3.2 Jam Code

3.2.1 Jam Codes (Related to Printer Unit)
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Code
0104
0208
010c
0210
0214
6
Display
Detail Code Main Cause/Symptom
Code
0000 Erroneous communication with card reader (serial communication)
- Disconnection from the card reader
has been detected since
communication started after
confirmation of normal connection to
the card reader (after power-on).
- A serial communication error has
occurred. (The serial communication
error cannot be recovered.)
0002 Erroneous communication with coin vendor (serial communication)
- Disconnection from the coin vendor
has been detected since
communication started after
confirmation of normal connection to
the coin vendor (after power-on).
- A serial communication error has
occurred. (The serial communication
error cannot be recovered.)
0000 Erroneous communication between controller and printer
Cannot communicate with the printer
at startup.
0000 CCU communication error
The installed modem PCB is
incompatible.
0000 Erroneous communication between controller and network board
The installed network board is
incompatible.
0000 Fan failure
The fan is faulty.
0000 Fixing drive circuit failure
- The heater does not turn on.
- A fixing drive motor failure was
detected.
Name Sensor No.
Delay jam in paper SR209
pickup section
Stationary jam in paper SR209
pickup section
Delay jam in deliver SR202,
section SR203,
SR209
Stationary jam in SR202,
delivery section SR203
Stationary jam in SR202,
machine SR203,
SR209
Countermeasure
- Check the connectors of the card reader and
image processor PCB.
- Replace the card reader for normal
connection.
- Replace the image processor PCB.
- Check the connection between the image
processor PCB and serial PCB.
- Check the connectors of the serial PCB and
coin vendor for normal connection.
- Replace the serial PCB.
- Check the coin vendor.
- Replace the image processor PCB.
- Check the connectors of the DC controller
PCB and image processor PCB for normal
connection.
- Check the power supply of the printer
(Check whether initialization is performed at
startup).
- Replace the DC controller PCB or image
processor PCB.
- Check the connectors of the image processor
PCB and modem.
- Replace the modem PCB.
- Replace the image processor PCB.
- Check the connectors of the image processor
PCB and LAN PCB for normal connection.
- Replace the LAN PCB.
- Replace the image processor PCB.
- Check the fan connector.
- Replace the fan.
- Replace the DC controller PCB.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the fixing drive motor.
- Replace the DC controller PCB.
- Replace the power supply PCB.
T-3-2
Description
The registration sensor cannot detect the leading edge of paper from
the moment paper pickup starts to the moment the jam detection
time is reached.
The registration sensor cannot detect the no paper status specified
time before the leading edge of the picked up paper reaches this
sensor.
- The fixing delivery sensor cannot detect presence of paper within
the specified time after turning on of the registration clutch.
- The fixing delivery sensor detected absence of paper within the
specified time after the sensor had detected presence of paper within
the specified time after turning on of the registration clutch.
- The No.1 delivery sensor cannot detect presence of paper within
the specified time after turning on of the fixing delivery sensor.
- The fixing delivery sensor cannot detect absence of paper within
the specified time after turning off of the registration clutch.
- The fixing delivery sensor cannot detect absence of paper within
the specified time after the sensor detected the leading edge of
paper.
- The No.1 delivery sensor cannot detect absence of paper within
the specified time after the sensor detected the leading edge of
paper.
Paper was detected in the paper transport path during initial
rotation, during automatic delivery, at the end of cleaning, or at
reception of an emergency stop command.
0011-2846