Table of Contents
Advertisement
Technical data, mains supply 1 x 220 - 240 V/3 x 200-240V
According to international standards
Output current
(3 x 200-240V)
Output power (230 V)
Typical shaft output
Typical shaft output
Max. cable cross
section, motor
Input current
(1 x 220-240 V)
Input current
(3 x 200-240 V)
Max. cable cross
section, power
Max. pre-fuses
3)
Efficiency
Power loss at 100%
load
Weight
4
Enclosure
1. American Wire Gauge. Max. cable cross
section is the largest cable cross section that can
be attached to the terminals. Always observe
national and local regulations.
2. Type gG pre-fuses must be used for installation
according to IEC rules. If you want to maintain UL/cUL
you must use pre-fuses of the type Bussmann KTN-R
200 V, KTS-R 500 V or Ferraz Shawmut, type ATMR
(max. 30A). The fuses must be placed for protection
in a circuit that is capable of supplying a maximum of
100,000 amps RMS (symmetrical), 500 V maximum.
3. Measured using a 65.5 ft (25 m) shielded/armoured
motor cable with a rated load and rated frequency.
4. IP20 is standard for VLT 2805-2875, whereas
NEMA 1 is an option.
100
VLT® 2800 Series
Type
2803
I
[A]
2.2
INV.
I
(60s) [A]
3.5
MAX
S
[KVA]
0.9
INV.
P
[kW]
0.37
M,N
P
[HP]
0.5
M,N
2
1)
[mm
/AWG]
4/10
I
[A]
5.9
L,N
I
(60s) [A]
9.4
L,MAX
I
[A]
2.9
L,N
I
(60s) [A]
4.6
L,MAX
2
1)
[mm
/AWG]
4/10
2)
IEC/UL
[A]
20/20
[%]
95
[W]
24
[lb]/[kg]
4.4/2.0 4.4/2.0 4.4/2.0 4.4/2.0 4.4/2.0 8.2/3.7 13.2/6.0
type
IP 20
2805
2807
2811
3.2
4.2
6.0
5.1
6.7
9.6
1.3
1.7
2.4
0.55
0.75
1.1
0.75
1.0
1.5
4/10
4/10
4/10
8.3
10.6
14.5
13.3
16.7
23.2
4.0
5.1
7.0
6.4
8.2
11.2
4/10
4/10
4/10
20/20
20/20
20/20
95
95
95
35
48
69
IP 20
IP 20
IP 20
MG.28.A8.22 - VLT is a registered Danfoss trademark
2815
2822
2840
6.8
9.6
16
10.8
15.3
25.6
2.7
3.8
6.4
1.5
2.2
3.7
2.0
3.0
5.0
4/10
4/10
4/10
15.2
-
-
24.3
-
-
7.6
8.8
14.7
12.2
14.1
23.5
4/10
4/10
4/10
20/20
20/20
25/25
95
95
95
94
125
231
IP 20
IP 20
IP 20
Advertisement
Table of Contents
