Download Print this page

Installing The Machine; Positioning The Machine; Water Connections; Water Inlet Hose - Westinghouse WSF6606 User Manual

Hide thumbs

Advertisement

Table of Contents

INSTALLING THE MACHINE

Positioning the machine

When considering the location for the dishwasher,
ensure that there is adequate space to enable
loading and unloading of the dishes
Do not put your machine in any location where
the ambient temperature can fall below 5°C .
Before positioning, take the machine out of its
packaging by following the warnings located on
the package .
Position the machine close to a water tap and drain .
You need to postion your machine, taking into
consideration that its connections will not be altered
once they are made .
Do not grip the machine by its door or panel in
order to move it .
Take care to leave a certain clearance from all sides of
the machine so that you can comfortably move
it back and forth during cleaning .
Make sure that the water inlet and outlet hoses do
not get squeezed while positioning the machine .
Also, make sure that the machine does not stand
on the electrical cable . Adjust the machine's feet so
that it is level and stable . Proper positioning of the
machine ensures problem-free opening and closing
of its door .
If the door of your machine does not close properly,
check if the machine is stable on the floor; if not,
adjust the feet and ensure it is level and stable .
Water connection
Ensure that the indoor plumbing is suitable for installing
a dishwasher and complies with AS/NZS 3500 . 1 .
Also, we recommend that you fit a filter at the entrance
of your place or apartment so as to avoid any damage to
your machine because of any contamination (sand, clay,
rust etc) that might be occasionally carried in through
the main's water supply or the indoor plumbing, and to
avoid problems of staining and formation of deposits
after washing .

Water inlet hose

the water pressure is above 1 MPa, a pressure-relief valve
should be installed .
WARNING
WARNING
Only turn the locking nut to secure hose - do not turn
8
INSTALLING THE MACHINE
Do not use the water inlet hose of
your old machine, you must use the
new water inlet hose supplied with
your machine . Before connecting
the water inlet hose to the water
tap, ensure clean water is flowing
from the tap before making the
connection . Connect the water inlet
hose directly to the water inlet tap .
The pressure supplied by the tap
should be at a minimum of 0 . 0 3
MPa and at a maximum of 1 MPa . If
the hose .
The first time you use the appliance, make sure that
there is no leakage .
The water inlet hose has a safety valve and a sheath
with an inner mains cable .
After the connections are made, the tap should be
turned on fully and checked for water tightness . For the
safety of your machine, make sure to always turn off the
water inlet tap after each wash program
is finished .
WARNING
WARNING
NOTE: Aquastop inlet hose has
components using 240V. Do not cut
Aquastop inlet hose. Do not let it get
folded, twisted, kinked or crushed.
WARNING
WARNING
NOTE: A water tempering valve is required if the water
temperature is
over 60°C.
WARNING
CAUTION
Always use new hoses when you connect the appliance
to the water mains . Old hoses must not be used . The
water inlet hose must be examined at an interval of twelve
months for deterioration and replaced if necessary .
In order to pass the safety valve through the kitchen
cabinets, an opening of at least 45mm x 90mm is
needed .
30cm
min .
Remove
entire
internal
membrane
Water drain hose
If you connect the water
drain hose to a trap spigot
under the sink, remove the
plastic membrane . If you
do not remove the entire
membrane, remaining food
can cause a blockage in the
drain hose spigot . Ensure a
hose clamp is used to secure
the hose to the spigot .

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for Westinghouse WSF6606