Table of Contents
Advertisement
QUICK START GUIDE
Switching on the machine
1
Press the POWER button
Progress indicator
You can follow the program flow using the progress
indicator lights located on the control panel .
Changing a program
If you would like to change programs while a washing
program is on .
After the dishwasher stops, select the desired
Cancelling a program
If you want to cancel current program for any reason .
Hold the PAUSE/START button for 3 seconds
8
QUICK START GUIDE
Once the POWER button is pressed,
the Start/Pause symbol illuminates
The Start/Pause button light
turns off once the program starts
and the WASH light is on
Select the program via
2
3
the PROGRAM button
Additonal functions
During the washing cycle
1
the WASH light is on
Once the program is completed the end light comes on
3
Do not open the dishwasher until this light comes on
Press the Pause/Start
button
2
program on the PROGRAM button
Press the Pause/Start
3
button to commence
new program
1
The END light starts flashing and water inside the
machine will drain for 30 seconds . The program is
cancelled when the END light stops flashing
INSTALLING THE MACHINE
Positioning the machine
When considering the location for the dishwasher,
ensure that there is adequate space to enable loading
and unloading of the dishes .
•
Do not put your machine in any location where
the ambient temperature can fall below 5°C .
•
Before positioning, take the machine out of its
packaging by following the warnings located on
the package .
•
Position the machine close to a water tap and drain .
You need to postion your machine, taking into
consideration that its connections will not be
altered once they are made .
•
Do not grip the machine by its door or panel in
order to move it .
•
Take care to leave a certain clearance from all sides of
Once completed
the machine so that you can comfortably move
the dry light will
it back and forth during cleaning .
illuminate and the
2
machine will run
•
Make sure that the water inlet and outlet hoses do
silently whilst drying
not get squeezed while positioning the machine .
Also, make sure that the machine does not stand
on the electrical cable . Adjust the machine's feet so
that it is level and stable . Proper positioning of the
machine ensures problem-free opening and closing
of its door .
•
If the door of your machine does not close properly,
check if the machine is stable on the floor; if not,
adjust the feet and ensure it is level and stable .
Water connection
Ensure that the indoor plumbing is suitable for installing
a dishwasher and complies with AS/NZS 3500 . 1 . Also,
we recommend that you fit a filter at the entrance of
1
your place or apartment so as to avoid any damage to
your machine because of any contamination (sand, clay,
rust etc) that might be occasionally carried in through
the main's water supply or the indoor plumbing, and to
avoid problems of staining and formation of deposits
after washing .
Water inlet hose
the water pressure is above 1 MPa, a pressure-relief valve
should be installed .
WARNING
WARNING
Only turn the locking nut to secure hose – do not turn
the hose .
2
•
The first time you use the appliance, make sure that
there is no leakage .
•
The water inlet hose has a safety valve and a sheath
with an inner mains cable .
After the connections are made, the tap should be
turned on fully and checked for water tightness . For the
safety of your machine, make sure to always turn off the
water inlet tap after each wash program is finished .
CAUTION
WARNING
Always use new hoses when you connect the appliance to
the water mains . Old hoses must not be used . The water
inlet hose must be examined at an interval of twelve
months for deterioration and replaced if necessary .
In order to pass the safety valve through the kitchen
cabinets, an opening of at least 45mm x 90mm is
needed .
Do not use the water inlet hose of
your old machine, you must use the
new water inlet hose supplied with
your machine . Before connecting
the water inlet hose to the water
tap, ensure clean water is flowing
from the tap before making the
Water drain hose
connection . Connect the water inlet
hose directly to the water inlet tap .
The pressure supplied by the tap
should be at a minimum of 0 . 0 3
MPa and at a maximum of 1 MPa . If
WARNING
WARNING
NOTE: Aquastop inlet hose has
components using 240V. Do not cut
Aquastop inlet hose. Do not let it get
folded, twisted, kinked or crushed.
WARNING
WARNING
NOTE: A water tempering valve is
required if the water temperature
is over 60°C.
30cm
min .
If you connect the water
drain hose to a trap spigot
under the sink, remove the
plastic membrane . If you
Remove
do not remove the entire
entire
membrane, remaining food
internal
can cause blockage in the
membrane
drain hose spigot . Ensure
a hose clamp is used to
secure the hose to the
spigot .
INSTALLATION
9
INSTALLING THE MACHINE
Hide quick links:
Advertisement
Table of Contents
