Related Manuals for Kauber InCeiling
Summary of Contents for Kauber InCeiling
- Page 1 CEILING PROJECTION SCREEN INSTALLATION GUIDE INCEILING...
- Page 3 Its smartly designed aluminum housing has many installation aids. In the Tensioned version it is additionally equipped with a special system to get an even more tense projection surface. The InCeiling series was created for suspend ceilings in both conference rooms and home cinemas.
-
Page 4: Package Contents
PACKAGE CONTENTS projection screen - 1 pcs side panel - 2 pcs fixing support - 2 pcs mounting holes template. - 1 pcs main hole template - 1 pcs holes marker - 1 pcs • ø1 M8 nut - 12 pcs. expansion dowel 0 - 6 pcs threaded rod - 4 pcs... -
Page 5: Screen Installation
SCREEN INSTALLATION 1. Carefully unpack the contents of the packaging, paying special attention to wooden sides that protect the contents of the carton from damage. Remember that one of them functions also as a template for mounting holes, so do not throw it out before the installation is finished! 2. - Page 6 Fig.2a 4. Hold the template, and then guide the marker through the holes in the template to mark the drilling of holes mounting in the fixed ceiling, (Fig.3). Fig.3 5. Using the ø10 drill, drill the holes for the mounting dowels in the marked places. The holes should be drilled in the correct order, starting with the hole marked on the template with the number 1 (Fig.4).
- Page 7 Fig.4 6. In place of the holes drilled in fixed ceiling, screw the mounting supports using the attached dowels and screws (Fig.5). NOTE! The mounting dowels supplied in the set can be used only for ceilings made of solid materials (for ex.
- Page 8 7. Threaded rods have to be cut to the appropriate length using the following formula: distance between the fixed ceiling rod length - 7 cm and the bottom edge of the suspended ceiling 8. After cutting, each of the threaded rods should be screwed into a suitable hole in the mounting support, and then countered with an M8 nut (Fig.6).
- Page 9 10. After connecting the power supply (see page no.15) slide the screen onto the mounted rods and screw each of the 4 M8 nuts using the included pipe wrench while checking the stability of the entire installation (Fig.8). A properly installed screen must be levelled. Correct the fixing by unscrewing or screwing the mounting nuts on the appropriate threaded rods.
- Page 10 11. The delivered screen has end positions set in accordance with the order. If the surface of the screen scrolls too low or not enough, correct the bottom end position using the included wrench. Before adjustment, check in the warranty card with what type of engine is your screen equipped with. NOTE! Adjustments to the end positions can only be made by a qualified person.
- Page 11 13. After completing the screen installation, peel off the foil protecting the cassette from damage (Fig.12, Fig.12a). Fig.12 Fig.12a -11-...
- Page 12 Adjusting the end positions (engine type "C" – you can check the engine type in the warranty card ) - Correcting the top end position (white end stop). White end stop Fig.13 White end stop Fig.14 - Correcting the bottom end position (yellow end stop). Yellow end stop Fig.15 Yellow end stop...
- Page 13 Adjusting the end positions (engine type "B" and "B-RTS" - check the engine type in the warranty card)) - Correcting the top end position (white end stop). White end stop Fig.17 White end stop Fig.18 - Correcting the bottom end position (yellow end stop). Yellow end stop Fig.19 Yellow end stop...
- Page 14 End positions adjustment (screen with built-in radio control – engine type "C-RTS") Correcting the bottom end position: 1. Using the remote control button UP set the roller-blind in the top end position. 2. At the same time, press and hold for more than 5 seconds buttons UP and DOWN. The drive moves briefly up / down.
-
Page 15: Electrical Connection
ELECTRICAL CONNECTION NOTE! The screen may only be connected to the power supply by a person with appropriate electrical qualifications. Before installing the screen cassette, lead the power supply cable to the place of installation and then connect it to the screen during installation according to the diagram A (Fig.23A) or according to the diagram B in the case of a screen with built-in radio control (Fig.23B). - Page 16 Connecting a key switch from the set. (The switch is available in the set for screen without a built-in radio control) Fig.24 -16-...
- Page 17 Diagram of connecting a key switch to the screen (screens with a "B" and "C" type engine) Contact Description Color Brown Phase (L) Blue Zero (N) Yellow-green Earthing Black Brown Fig.25 -17-...
-
Page 18: Technical Data
D=B+100mm F=A+208mm J=A+130mm K=50mm H=121mm G=A+248mm INCEILING + BLACK FRAME + BLACK STRIP A- width of active surface B - height of active surface C = A +100mm D = B +50mm + black strip height F = A +208mm... - Page 19 C = A +100mm D=B+100mm F=A+360mm J=A+270mm K=50mm H=121mm G=A+400mm INCEILING + TENSIONERS + BLACK STRIP A- width of active surface B - height of active surface C = A +100mm D = B +50mm + black strip height F = A +360mm...
- Page 20 Thank you for choosing the KAUBER screen. We invite you to purchase other KAUBER products -20-...