Advertisement
Quick Links
Advertisement
Related Manuals for Kauber BLUE LABEL
Summary of Contents for Kauber BLUE LABEL
- Page 1 PROJECTION SCREEN INSTALLATION GUIDE BLUE LABEL...
- Page 3 Blue Label is a series of electric projection screens in anodized aluminum housings. A timeless design and a wide selection of projection surfaces make it the most-chosen screen for home theater and conference rooms. In the Tensioned version it is additionally equipped with a special system of tensioners to get an even more tense projection surface.
-
Page 4: Screen Installation
SCREEN INSTALLATION 1. Using the screws (c), attach mounting brackets to the sides of the screen (a) depending on the mounting method (b) in the wall position (fig. 1a) or ceiling one (fig.1b) Wall mounting Fig.1a Ceiling mounting Fig.1b... - Page 5 2. Depending on the method of mounting, screw the mounting brackets using the mounting dowels to the wall (Fig.2a) or to the ceiling (Fig.2b). NOTE! The mounting dowels provided in the set can be used only for ceilings and walls made of solid materials (for ex.
- Page 6 Fig.3 4. In Blue Label Tensioned screens - once the surface is fully unfolded, you can use the allen key to adjust the tensioning force (if necessary) with the screws located on both sides of the bottom bar.
- Page 7 Adjusting the end positions (engine type "C" – you can check the engine type in the warranty card ) -Correcting the top end position (white end stop). White end stop Fig.4 White end stop Fig.5 -Correcting the bottom end position (yellow end stop). Yellow end stop Fig.6 Yellow end stop...
- Page 8 Adjusting the end positions (engine type "B" and "B-RTS" - check the engine type in the warranty card)) - Correcting the top end position (white end stop). White end stop Fig.8 White end stop Fig.9 - Correcting the bottom end position (yellow end stop). Yellow end stop Fig.10 Yellow end stop...
- Page 9 End positions adjustment (screen with built-in radio control – engine type "C-RTS") Correcting the bottom end position: 1. Using the remote control button UP set the roller-blind in the top end position. 2. At the same time, press and hold for more than 5 seconds buttons UP and DOWN. The drive moves briefly up / down.
-
Page 10: Electrical Connection
ELECTRICAL CONNECTION NOTE! The screen may only be connected to the power supply by a person with appropriate electrical qualifications. Before installing the screen cassette, lead the power supply cable to the place of installation and then connect it to the screen during installation according to the diagram A (Fig.14A) or according to the diagram B in the case of a screen with built-in radio control (Fig.14B). - Page 11 Connecting a key switch from the set. (The switch is available in the set for screen without a built-in radio control) Fig.15 -11-...
- Page 12 Diagram of connecting a key switch to the screen (screens with a "B" and "C" type engine) Contact Description Color Phase (L) Brown Zero (N) Blue Earthing Yellow-green Black Brown Fig.16 -12-...
-
Page 13: Technical Data
A- surface width B- surface height F = A+64mm J=A+30mm K=50mm H=105mm G=A+112mm M=A+88mm N=60mm BLUE LABEL + BLACK FRAME A- width of active surface B - height of active surface C = A +100mm D=B+100mm F=A+164mm J=A+130mm K=50mm H=105mm... - Page 14 BLUE LABEL + BLACK FRAME + BLACK STRIP A- width of active surface B - height of active surface C = A +100mm D = B+50mm + height of the black strip F = A +164mm J=A+130mm K=50mm H=105mm G=A+212mm...
- Page 15 Technical specifications: Power supply: 230V 50Hz 120W – screen without a built-in radio control Power: 120W – screen with built-in radio control -15-...
- Page 16 Thank you for choosing the KAUBER screen. We invite you to purchase other KAUBER products -16-...