Kenmore 110.4443 Series Use & Care Manual page 5

Alternate Parts
Your installation may require additional parts. For information
on ordering, please refer to the back cover of this manual.
If You Have:
Laundry tub or standpipe
taller than 72" (183 cm)
1" (2.5 cm) diameter
standpipe
Overhead sewer
Floor drain
Water faucets beyond reach
of fill hoses
Drain hose too short
Drain hose that is too long
Lint clogged drain
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See "Drain System."
Washer Dimensions
(533 mm)
37"
(940 mm)
/ "
3
4
(19 mm)*
*Minimum measurement with leveling feet installed.
IMPORTANT: Do not install or store the washer where it will
be exposed to the weather.
Proper installation is your responsibility.
You Will Need to Buy:
Sump pump system
(if not already available)
2" (5 cm) diameter to
1" (2.5 cm) diameter
standpipe adapter,
Part Number 3363920
Standard 20 gal. (76 L)
39" (990 mm) tall drain tub
or utility sink, sump pump,
and connectors (available
from local plumbing suppliers)
Siphon break, Part Number
285320; additional drain
hose, Part Number 3357090
and connector kit,
Part Number 285442
2 longer water fill hoses:
6 ft (1.8 m)
Part Number 76314
10 ft (3.0 m)
Part Number 350008
Drain hose, Part Number
388423 and hose kit,
Part Number 285442
Hose kit, Part Number
285442
Drain protector,
Part Number 367031
21"
23"
(584 mm)
You will need:
A water heater set to deliver 120°F (49°C) water to
■
the washer.
A grounded electrical outlet located within 5 ft (1.5 m) of
■
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 3½ ft (1.1 m)
■
of the hot and cold water fill valves, and water pressure of
5–100 psi (34.5–690 kPa).
A level floor with a maximum slope of ¾" (1.9 cm) under
■
entire washer. Installing the washer on carpeting is not
recommended.
A sturdy floor to support the washer weight (washer, water,
■
and load) of 225 lbs (102 kg).
Do not store or operate your washer in temperatures at or
below 32°F (0°C). Some water can remain in the washer and
can cause damage in low temperatures. See "Washer Care"
for winterizing information.
Recessed area or closet installation
The dimensions shown are for the recommended spacing
allowed, except the closet door ventilation openings. The
dimensions shown for the closet door ventilation openings
are the minimum required.
Additional spacing should be considered for ease of
■
installation and servicing.
Additional clearances may be required for wall, door,
■
and floor moldings.
Additional spacing of 1" (2.5 cm) on all sides of the washer
■
is recommended to reduce noise transfer.
If a closet door is installed, the minimum air openings
■
in the top and bottom of the door are required. Louvered
doors with air openings in the top and bottom are
acceptable.
Companion appliance spacing should also be considered.
■
Washer Only
4"
(102 mm)
1"
(25 mm)
Recessed area
3"
(76 mm)
48 in. 2
(310 cm 2 )
12"
(305 mm)
24 in. 2
1"
(155 cm 2 )
(25 mm)
1"
(25 mm)
3"
(76 mm)
Closet door with vents
5