CIRCUIT DIAGRAM(回路図) SERVICE CHECK PROGRAM DETAIL VIEW OF DM CIRCUIT BOARD TEST POINTS (サービス検査プログラム) ......65/87 (DM シートのテストポイント詳細図 ) UPDATING THE PROGRAM (プログラムのアップデート) .......109/112 011875 HAMAMATSU, JAPAN n8: 20070625-120750 n12: 20070625-168000 Copyright (c) Yamaha Corporation. All rights reserved. PDF ’07.07...
Page 2
IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
Page 4
LEVEL Control −∞ to +6 dB (to STEREO bus)/0 dB (to C-R) 2TR IN To C-R OUT, STEREO bus ON Switch ON/OFF AD Converter 24 bit linear, Enhanced dual-bit delta/sigma conversion STEREO Fader −∞ to +10 dB ST OUT −∞...
Page 5
INPUT A (Mono) XLR type balanced, CH1−8 (n12) −60 dBu to +10 dBu +24 dBu 3.5 kΩ +48 V Phantom powered CH1−4 (n8) INPUT B (Mono) 3.5 kΩ CH1−8 (n12) TRS phone type, balanced −60 dBu to +10 dBu +24 dBu (500 kΩ...
Page 6
→ DIRECT OUT、REC バス、 STEREO バス GAIN コントロール 44 dB 可変 (-60 dB ∼ -16 dB) PHASE スイッチ 正相 / 逆相 (CH1 ∼ 7 (n12)、CH1 ∼ 3 (n8)) ハイパスフィルタースイッチ OFF/80 Hz (-12 dB/oct.) Hi-Z スイッチ ON/OFF (CH8 (n12)、CH4 (n8))、入力インピーダンス : 500 k Ω...
Page 7
2TR IN LEVEL コントロール - ∞ ∼ +6 dB ( → STEREO バス )/0 dB ( → C-R) → C-R OUT、STEREO バス ON スイッチ ON/OFF AD コンバーター 24 bit リニア、高性能デュアルビットデルタ / シグマ変換 ST OUT STEREO フェーダー - ∞ ∼ +10 dB - ∞...
PANEL LAYOUT(パネルレイアウト) 1. Top Panel(トップパネル) <n8> <n12> q Channel Control section: (∆P.10) q チャンネルコントロール部: (∆P.10) w Master Control section: (∆P.11) w マスターコントロール部: (∆P.11) e Meter section: (∆P.12) e メーター部: (∆P.12) r Control Room section: (∆P.13) r CONTROL ROOM 部: (∆P.13)...
Page 10
1-1. Channel Control section(チャンネルコントロール部) q [GAIN] control w [PAD] switch switch (high pass fi lter) r PHANTOM [+48V] switch t [PHASE] switch y [Hi-Z] switch u [INPUT SELECT] switch i Compressor controls • [MORPH] control • [DRIVE] control • [COMP] LED o Equalizer (EQ) •...
Page 11
1-2. Master Control section(マスターコントロール部) q Reverb section • REVERB [TYPE] switch • [REVERB TIME] control • REVERB [LEVEL] control • [TO AUX]/[TO REC]/[TO ST] switches w 2TR TO ST section • [LEVEL] control • [ON] switch e DAW TO ST section •...
Page 12
1-3. Meter section(メーター部) <n8> <n12> q Microphone (n12 only) q マイクロフォン(n12 のみ) w [SOLO LEVEL] control (n12 only) w [SOLO LEVEL] コントロール(n12 のみ) e [DAW TO AUX] control e [DAW TO AUX] コントロール r [AUX LEVEL] control (n12 only) r [AUX LEVEL] コントロール(n12 のみ)...
Page 15
2. Rear Panel(リアパネル) <n8> <n12> q ANALOG INPUT jacks (monaural) q INPUT 端子 ( モノラル ) • INPUT A jacks ・INPUT A 端子 • INPUT B jacks ・INPUT B 端子 w INSERT I/O jacks w INSERT I/O 端子 e ANALOG INPUT jacks (stereo) e INPUT 端子...
DISASSEMBLY PROCEDURE (n8)(分解手順) Precautions(注意事項) ※ 束線止めは、取り外す前と同じように取り付けてく Install the cord binders as they were installed ださい。 before removal. After replacing the DM-A, PN-A circuit boards ※ DM-A シート、 PN-A シート、 フェーダーを交換後は、 and fader, be sure to calibrate the faders. (See フェーダーのキャリブレーションを実施してくださ...
DISASSEMBLY PROCEDURE (n12)(分解手順) Precautions(注意事項) ※ 束線止めは、取り外す前と同じように取り付けてく Install the cord binders as they were installed ださい。 before removal. After replacing the DM-B, PN-B, PNSB circuit ※ DM-B シート、PN-B シート、PNSB シート、フェー boards and fader, be sure to calibrate the faders. ダーを交換後は、フェーダーのキャリブレーション...
Page 26
Side cover L [80B] Rear panel (サイドカバー左) assembly (リアパネル [200A] [280A] アセンブリー) [70A] Side angle R (サイド金具右) [50] [80A] Side cover R (サイドカバー右) Front cover (フロントカバー) [160] [180] [100B] [220A] [350] [100A] Holder R assembly DM-B (固定金具Rアセンブリー) RGB assembly [110A] (RGBアセンブリー)...
Page 27
RGB Assembly, REG Circuit Board RGB アセンブリー、REG シート (所要時間:約 4 分) (Time required: About 4 minutes) Remove the bottom cover. (See procedure 4) ボトムカバーを外します。 (4 項参照) Remove the three (3) screws marked [320B]. The [320B] のネジ 3 本を外して、RGB アセンブリー...
Page 28
MIDI-B Circuit Board MIDI-B シート (所要時間:約 11 分) (Time required: About 11 minutes) サイドカバー左を外します。 (1 項参照) Remove the side cover L. (See procedure 1) サイドカバー右を外します。 (2 項参照) Remove the side cover R. (See procedure 2) フロントカバーを外します。 (3 項参照) Remove the front cover. (See procedure 3) ボトムカバーを外します。...
LSI PIN DESCRIPTION(LSI 端子機能表) 1394AV-LINK (X6893A00) DICEII ....................36/37 AK4393-VS-E2 (XW029A00) DAC (Digital to Analog Converter) ............38 AK5359VT-E2 (X7730A00) ADC (Analog to Digital Converter) (n12 only) ..........38 AK5385BVF-E2 (X5364B00) ADC (Analog to Digital Converter) ............38 MB87S1280 (X6363A00) SSP1 (MAIN) ....................35 MB87S1280 (X6363A00) SSP1 (SUB) ....................35...
Page 35
MB87S1280 (X6363A00) SSP1 (MAIN) DM-A: IC107, 110 (n8) MB87S1280 (X6363A00) SSP1 (SUB) DM-B: IC107, 110 (n12) NAME FUNCTION NAME FUNCTION WAITN Wait for external CPU MD[7] Data bus(ARM,DSP -> memory) IRQN_OUT Output of interrupt information MD[6] Data bus(ARM,DSP -> memory) VDDE VDDE +3.3V...
Page 36
1394AV-LINK (X6893A00) DICE II MLAN: IC106 OUTER OUTER NAME FUNCTION NAME FUNCTION VSS3OP – I/O ground TEMO Test mode pin SRAM_WE SRAM write enable TCB[7] Test pin VDD3OP – I/O 3.3V GPIO4/SRAM_READY General purpose I/O / SRAM ready (read enable)
Page 37
MLAN: IC106 OUTER OUTER NAME FUNCTION NAME FUNCTION VSS3OP – I/O ground AES_RX2 AES3 Receiver ch4/5 Address bus VDD3OP – I/O 3.3V DSAI_RX1 DSAI Receiver 1 data line VSS3OP – VSS3OP – I/O ground VSS3OP – DSAI_SYNCD DSAI Sync D...
Page 38
DM-A: IC174, 175, 182-184 (n8) AK5385BVF-E2 (X5364B00) ADC (Analog to Digital Converter) DM-B: IC172-175, 182-184 (n12) NAME FUNCTION NAME FUNCTION VREFL Lch voltage reference input SDTO Audio serial data output AVSS – Analog ground CKS1 Master clock select 1...
Page 39
Voltage output 1 ON/OFF2 2 output ON/OFF control and soft start control MODE DC-DC converter operation mode setting 1 voltage setting Non-connection DM-A: IC111 (n8) XC9572XL-10VQG64C (X7748A00) CPLD (Complex Programmable Logic Device) DM-B: IC111 (n12) NAME FUNCTION NAME FUNCTION Input / Output...
Page 40
Test control input Test control input Digital power supply Analog power supply DGND Digital ground AGND Analog ground DGND PN-A: IC100, 200 (n8) PN-B: IC100, 200 (n12) μPD780031AYGK-N09 (XZ916300) E-PNS2a LED/SWITCH DRIVER PNSB: IC1 (n12 only) NAME FUNCTION NAME FUNCTION P50/A8...
Page 44
DM-A Circuit Board (n8) DM-B Circuit Board (n12) to HA-A (ANALOG INPUTS ch1-4) -CN100 (n8) not installed (n8) to HA-A (ANALOG INPUTS ch1-4)-CN102 (n8) HA-B (ANALOG INPUTS ch1-4) to PNSB-CN2 (n12) HA-B (ANALOG INPUTS ch1-4)-CN102 (n12) -CN100 (n12) to PN-A-CN1 (n8)
Page 45
JK-A-CN100 (n8) not installed (n8) JK-B-CN100 (n12) to HA-A (ANALOG INPUTS ch5-8)-CN100 (n12) to JK-A-CN103 (n8) to JK-A-CN102 (n8) JK-B-CN103 (n12) to PS-CN106 JK-B-CN102 (n12) not installed (n8) not installed (n8) to JK-B-CN101 (n12) to JK-B-CN104 (n12) not installed (n8)
Page 47
MIDI-A-CN200 (n8) not installed not installed MIDI-B-CN200 (n12) to PS-CN101 to PN-A-CN500 (n8) PN-B-CN500 (n12) not installed (n8) to PNSB-CN200 (n12) Pattern side(パターン側) DM-A, DM-B: 2NA-WH29160...
Page 48
HA-A Circuit Board (n8/n12) HA-B Circuit Board (n12) to PS-CN105 (n8) HA-B (ANALOG INPUTS ch1-4): to DM-A-CN118 (n8) to PS-CN104 (n12) to DM-A-CN105 (n8) HA-B (ANALOG INPUTS ch1-4): HA-A (ANALOG INPUTS ch5-8): HA-B (ANALOG INPUTS ch1-4): to DM-B-CN118 (n12)
SERVICE CHECK PROGRAM 1. Test Program This test program is used for “service test” of the n8 or n12. The panel controls (keys, encoders, and LED indicators) tests cannot be automatically judged and they should be determined by visual inspection.
Page 66
1-3. Locations of Starting/Selecting keys Selecting key <n8> MUTE ON/OFF test Starting/Selecting keys LED test SWITCH test VOLUME test Starts test program of service test mode Aborts SWITCH test · Aborts VOLUME test · Aborts LED test · LED test (including termination) ·...
Page 67
65.) the results of memory check, switch, and LED tests are OK and (2) Run the service test program with the n8 or n12. (Refer to the results of other tests are NG or the remaining items have “1-4. How to start” on page 67.) not been tested.
Page 68
“YAMAHA USB OUT 0-1” for MIDI output and click (10) Execute “Send Sysex” of “Command Windows” menu in “OK”. (Photo 4) the toolbar. (Photo 7) (*1) (Photo 4) (Photo 7) *1 Make sure that “YAMAHA USB IN 0-1” is not included in this fi eld.
Page 69
(11) Test results will appear. (Photo 8) • Example of executing screen • Example of executing screen (Photo 8) 2. Service test 2-1. Memory check (01 CPU/MEMORY) 2-1-1. Outline Executes read/write tests of the fl ash ROM and RAM connected * Refer to “3.
Page 70
• Example of executing screen * Refer to “3. List of test items” for details. (Page 80) 2-2-4. In case of executing tests from n8 or n12 Press the [MONITOR REMOTE: ON] key and [MONITOR REMOTE: REC BUS] key simultaneously to start the test.
Page 71
• Order for pressing switches FOOT SW <n8>...
Page 72
• Order for pressing switches FOOT SW <n12>...
Page 75
* Refer to “3. List of test items” for details. (Page 80) F/W 3/4 to 13/14 F/W 1/2 to 11/12, 15/16 2-4-4. In case of executing tests from n8 or n12 Press the [MONITOR REMOTE: ON] key and [CLICK SSP1 (Main) SSP1 (Sub) REMOTE: ON] key simultaneously to start the test.
Page 76
• SSP1 (Main) ⇔ SSP1 (Sub) A-BUS connection test Personal computer A-BUS uses 16-line mode. Transmits test data of about 16 ch from Main to Sub, and from Sub to Main using frame A, and reads at reception side, and judges as OK if the data is the...
Page 77
* Refer to “3. List of test items” for details. (Page 80) 2-9-3. Execution of test from PC By transmitting MIDI command, switches Hi-Z ON/OFF of CH 4 in case of the n8 or Hi-Z ON/OFF of CH 8 in case of the 2-7. MUTE ON/OFF test n12.
Page 78
LEDs of A.IN in INPUT SELECT indicate which connection 2-11-2. Test contents The SSP1 queries the DICEII on how many nodes are detected. mode is selected. If three nodes (two connector and itself) are detected, the 1) Normal mode: A.IN LED of CH 1 lights up...
Page 79
fl ash ROM necessary for adjustment in order to minimize piece-to-piece variations of resistors in the fader parts. Restarting the power of the n8 or n12 adjusts the A/D value of the faders according to the data obtained in the above- mentioned procedures.
Page 80
Starts volume input test A0 43 00 input test If the switch for stopping the volume input test of the n8 or Stops volume input n12 is pressed, instructions to stop the test will be transmitted n8 or n12 " PC...
Page 81
A0 48 00 F0 43 02 01 00 F7 MUTE OFF test Executing HI-Z ON PC " n8 or n12 HI-Z of CH 8 (CH 4 in case of n8) is turned on. A0 49 00 F0 43 02 XX 01 F7 test HI-Z test (09) Executing HI-Z OFF PC "...
Page 82
4. Factory set procedure • Locations of Starting keys <n8> Starting keys <n12> Starting keys Turning on the power while holding down the three keys, (6) Then, initialization of the information data of 1394 wiring [MUTE], [2TR] and [ST], simultaneously initializes the...
Page 83
*1: Connect plugs at the same time to the ST CH LINE L/R Specifi cations of input signal to each input terminal is as follows: pair connectors. (i.e. n8: 5 (L) and 6 (R), 7 (L) and 8 (R) / n12: 9 (L) and 10 (R), 11 (L) and 12 (R))
Page 84
1-2-5. Equivalent input noise Set up as in descriptions marked w, r, y, i and !3 in · Turn on the PAD switch of input CH 1-4 (n8)/CH 1-8 (n12). procedure 1-2-2. Connect 150 Ω resistor to the input terminals as follows: *1: Connect 150 Ω...
Page 85
C-R OUT A-C (n12) 1-3-1. Preparations -90 or less PHONES Set the n8 or n12 to AD/DA through (Output test mode) for test. Refer to “2-12. AD/DA through connection” for details of -90 or less PHONES setup procedure and internal connection. (Page 78) ·...
Page 86
AUX OUT 0.03 % or less (n12 のみ ) 1-3-8. PHONES Volume attenuation C-R OUT (n8) Set up as in description marked !4 in procedure 1-3-2. C-R OUT A-C (n12) 0.03 % or less Set up the controller as follows: AUX PHONES 0.1 % or less...
UPDATING THE PROGRAM • Locations of starting keys and version indication Version indication <n8> Starting/Selecting keys Version upgrade Version checking Version indication <n12> Starting/Selecting keys Version upgrade Version checking...
Page 110
1. Version Checking of Main Unit Firmware (1) Turn on the power while holding down the [ ] (STOP) key, and LEDs at the L side of the MASTER LEVEL METER will indicate BOOT version and the LEDs at the R side will indicate PROGRAM version.
Page 111
2. How to Upgrade the Main Unit Program Turn on the power while simultaneously holding down the [PREV] key and [MONITOR REMOTE REC BUS] key to enter the PROGRAM fi rmware writing mode. When the fi rmware writing mode is started, the topmost LED at the L side of the MASTER LEVEL METER will light.
Page 113
1. 本体ファームウェアバージョン確認方法 (1) [ ] (STOP) キーを押しながら電源を入れることで、 MASTER LEVEL METER の L 側の LED に BOOT 部のバージョン、 R 側の LED に PROGRAM 部のバージョンを表示します。 BOOT 部バージョン表示 OVER OVER 0000 BOOT 部 メジャーバージョン LED を 2 進数と見立てて、 4 つの LED で 0∼15 (F) を...
Page 114
2. 本体プログラムバージョンアップ方法 [PREV] キーと [MONITOR REMOTE REC BUS] キーを同時に押しながら電源を入れると、PROGRAM 部のファーム書き込 みモードに入ります。 ファーム書き込みモードに入ると、MASTER LEVEL METER の L 側の一番上の LED が点灯表示します。 この後、アップデート用データを受信することによりファーム書き込みが開始されます。 MASTER LEVEL METER の R 側はファーム書き込みの進捗状況を表示します。 ファーム書き込み中に本体の電源を OFF しないでください。 ファーム書き込みが完了すると、自動的に通常プログラムが起動します。 ファーム書き込み中にエラーが発生した場合は、R 側のすべての LED が点滅表示となり、通常プログラムに移行しません。 最初からバージョンアップを行ってください。 ※ アップデート用プログラムは、YSISS ホームページよりダウンロードしてください。 ファーム書き込み...
1-2. Power source INPUT SELECT: A.IN Use the voltage appropriate for destination with allowable COMP DRIVE Volume (CH 1-4 (n8)/CH 1-8 (n12)): tolerance of maximum ±10 %. Use the following AC adaptor. • n8 COMP MORPH Volume (CH 1-4 (n8)/CH 1-8 (n12)):...
*3: Check that level difference between L/R channels are as *1: Connect plugs at the same time for ST CH LINE L/R pair follows: connectors. (i.e. n8: 5(L) and 6(R), 7(L) and 8(R) / n12: Tolerance 9(L) and 10(R), 11(L) and 12(R)) 4 dB or less *2: Turn on the “2TR TO ST”...
Page 117
2TR IN L 2TR IN L and R Others 2TR IN R CH 5-8 (LINE) (n8) -58 (EIN: -88) CH 9-12 (LINE) (n12) 2TR IN -66 (EIN: -84) · Turn on the PAD switch of CH 1-4 (n8)/CH 1-8 (n12).
Page 118
AUX PHONES INPUT Fader of CH 1 and 2: INPUT LEVEL STEREO BUS Fader: ON SW of CH 3-8 (n8)/CH 3-12 (n12): CH A 1 -78 or less – -78 or less – Off (Refer to the following descriptions for CH A 2 –...
*1: Connect plugs at the same time for ST CH LINE L/R pair is inserted. connectors. (i.e. n8: 5(L) and 6(R), 7(L) and 8(R) / n12: 9(L) and 2-2-14. MUTE 10(R), 11(L) and 12(R)) Set up the controller as follows: AUX/C-R PHONES Volumes: 3.
Page 121
PAN Volume of MONO 偶数 CH CONTROL ROOM LEVEL Volume: (i.e. CH 2,4 (n8)/CH 2,4,6,8 (n12)): C-R SOURCE SELECT SW: R(時計回り振り切り) C-R PHONES Volume: BAL Volume of CH 5-8 (n8)/CH 9-12 (n12): AUX PHONES Volume: Center BAL Volume of STEREO BUS: Center Unit: [dBu] all of CH Fader: 公称...
Page 122
CH 12 (n12) CH 5-8 (LINE) (n8) -58 (EIN: -88) CH 9-12 (LINE) (n12) 2TR IN L 2TR IN L and R Others 2TR IN R 2TR IN -66 (EIN: -84) ・入力 CH 1-4 (n8)/CH 1-8 (n12) の PAD スイッチを ON にします。...
Page 123
ST OUT (RCA) (n12 のみ ) INPUT CH A 1-4 (n8)/1-8 (n12): INPUT 2pin(Hot) と 3pin(Cold) の間 +6.2 INPUT CH 5-8 (LINE) (n8)/9-12 (LINE) (n12) : CH A 1 (output) -58 以下 (output) -68 以下 (output) -58 以下 Tip と Sleeve の間...
Page 124
*1: 対になる ST CH LINE L/R の端子には同時にプラグ 2-2-14. MUTE(ミュート) を挿します。 下記のように操作子を設定します。 ( つ ま り n8: 5(L) と 6(R)、7(L) と 8(R)/n12: 9(L) と AUX/C-R PHONES Volumes: 10(R)、11(L) と 12(R)) GAIN Volumes of CH 1-8 (n8)/CH 1-12 (n12): MIN 3. 音出し・機能検査...
Check that the “/RESET” signal level of each device is at High (+3.3 V typ.). “/RESET” signal source: DM-A circuit board (n8)/DM-B circuit board (n12) IC104-1 pin Reset cancellation factor: Detecting that core voltage of SSP1 (IC107, IC110) is 1.65 V or more.
Page 126
DM-A circuit board (n8)/DM-B circuit board (n12): IC115-17 pin Check that the signal level of the E-/IC(E-PNS2a) is at High. DM-A circuit board (n8)/DM-B circuit board (n12): IC111-59 pin (3.3 V typ.) CPLD DM-A circuit board (n8)/DM-B circuit board (n12): IC120,121-4 pin (5.0 V typ.) DM-A circuit board (n8)/DM-B circuit board (n12): CN110,111-1 pin (5.0 V typ.)
Page 127
Check that levels at each control line (SDA, SCL) between the I C and E-BUS micon are moving. E-BUS PN-A circuit board (n8)/PN-B circuit board (n12): IC100,IC200 DM-A circuit board (n8)/DM-B circuit board (n12): IC115 PNSB circuit board (n12 only): IC1...
Full-scale input: 2.9 Vp-p AGND (phase opposite to the hot side phase). * CH5 on n8 TL227 ADI[10]-(+) A/D converter input hot side of INPUT CH10. * CH6 on n8 Full-scale input: 2.9 Vp-p AGND ADI10 A/D converter input cold side of INPUT CH10...
Page 132
Data output of A/D converter (IC182) of INPUT CH9,10. TL242 ADO5 ADO[5] +3.3 V 24 bit MSB-First DGND * CH5,6 on n8 Data output of A/D converter (IC183) of INPUT CH11,12. TL243 ADO6 ADO[6] +3.3 V 24 bit MSB-First DGND...
Page 133
Master clock for A/D, D/A converter. 256-fold of sampling frequency TL253 256FS 256Fs DGND * Provided by the MLAN circuit board. 3.3 Vp-p Bit clock for A/D, D/A converter. 64-fold of sampling frequency TL254 64FS 64Fs DGND * Provided by the MLAN circuit board.
Page 134
TL260 TL207 TL205 TL206 TL259 TL204 TL208 2. Checking A/D input ADI1 to ADI14 Each point of ADI1 to ADI14 has 2 test lands and their phases are opposite to each other while the signal level is the same.
Page 135
3. Checking A/D output ADO1 to ADO8 Digital audio signal with the signal amplitude of approximately 3.3 V, MSB fi rst 24 bit is detected at ADO1 to ADO8. Set the word clock of the TL255 at trigger source to observe with an oscilloscope as 2 ch signals are transferred through one signal line with time-division way.
Page 136
TL248 TL247 TL252 TL251 TL250 TL246 (TL255) TL249 5. Checking D/A output Because board density for the D/A output is too large, dedicated test lands are not equipped. Use lands on chip resistors instead for observation. R393 R394 R392...
Page 137
R290 R289 R294 R293 R292 R291 These test points are outputs of Op-Amp that make differential output of D/A converter into single end output. The reference GND is TL260 (AGND). 6. Checking audio synchronized clock TL104 (128FS) Clock with frequency 128-fold of sampling frequency and signal amplitude of 3.3 V.
Page 138
The clock is supplied by the MLAN circuit board and provided to SSP1, A/D converter and D/A converter from the 100-pin connector (CN109) through IC118. The reference GND is TL258 (DGND). TL254 TL253 TL255 TL104 Timing relation of each clock is shown in the following table.
Page 139
TL257 (L:MUTE-REQ) L:MUTE-REQ is a signal that mutes analog output and audio output to IEEE1394 (DAW I/O) when request for muting is produced from the MLAN circuit board. When the point is “L” level (0 V), all muting circuits...
Page 149
MIDI IMPLEMENTATION CHART YAMAHA [ DIGITAL MIXING STUDIO ] Date :5-Oct-2006 Version :1.0 Model n8/12 MIDI Implementation Chart Function... Transmitted Recognized Remarks Basic Default Channel Changed Mode Default Messages Altered ************** Note : True voice ************** Number Velocity Note ON...
Page 150
PARTS LIST CONTENTS(目次) OVERALL ASSEMBLY(総組立) ..............2 TOP PANEL ASSEMBLY(トップパネルアセンブリー) ........4 REAR PANEL ASSEMBLY(リアパネルアセンブリー) .........6 ELECTRICAL PARTS(電気部品) .............8-31 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model T : Taiwan model...
Page 151
OVERALL ASSEMBLY(総組立) Rear panel assembly: See page 6. RGB assembly (リアパネルアセンブリー) (RGBアセンブリー) 310c 310b 310d 310c 310a 310d Top panel assembly: See page 4. (トップパネルアセンブリー)...
Page 152
PART NO. DESCRIPTION 部 品 名 REMARKS REF NO. QTY RANK OVERALL ASSEMBLY 総 組 立 n8 Overall Assembly 総 組 立 (WH22300) Top Panel Assembly トップパネルアセンブリー (WH22520) WH224300 Side Angle L LEFT サ イ ド 金 具 左 塗 装 品...
Page 153
TOP PANEL ASSEMBLY(トップパネルアセンブリー) Accessories (付属品)...
Page 180
PS/REG PART NO. DESCRIPTION 部 品 名 REMARKS REF NO. QTY RANK CN101 LB932060 Base Post Connector VH 6P TE ベ ー ス ポ ス ト CN102 LB918020 Base Post Connector XH 2P TE ベ ー ス ツ キ ポ ス ト CN103 LB918020 Base Post Connector XH 2P TE ベ...
Page 181
PARTS LIST CONTENTS(目次) OVERALL ASSEMBLY(総組立) ..............2 TOP PANEL ASSEMBLY(トップパネルアセンブリー) ........4 REAR PANEL ASSEMBLY(リアパネルアセンブリー) .........6 ELECTRICAL PARTS(電気部品) .............8-38 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model T : Taiwan model...
Page 182
OVERALL ASSEMBLY(総組立) Rear panel assembly: See page 6. (リアパネルアセンブリー) RGB assembly (RGBアセンブリー) 310c 310b 310d 310c 310a 310d Top panel assembly: See page 4. (トップパネルアセンブリー)...
Page 183
PART NO. DESCRIPTION 部 品 名 REMARKS REF NO. QTY RANK OVERALL ASSEMBLY 総 組 立 n12 Overall Assembly 総 組 立 (WH22240) Top Panel Assembly トップパネルアセンブリー (WH22360) WH225000 Side Angle L LEFT サ イ ド 金 具 左 WF419300 Hex. Socket Set Screw-S 3.0X6 MFZN2B3 S...
Page 184
TOP PANEL ASSEMBLY(トップパネルアセンブリー) Accessories (付属品)...
Notation for Circuit Diagrams (回路図表記上の注意) 1. How to identify inter-sheet connectors (シート間コネクタの読み方について) This indicates the destination page. Signal name (信号の行先ページ数を示します。) (信号名) This indicates the location of the counter inter-sheet connector. (The alphabet indicates horizontal direction and the number indicates vertical direction) 対応するシート間のコネクタのあるロケーションを示します。...
Page 221
BLOCK DIAGRAM 001 (n8/n12) n8/n12 ANALOG INPUTS Address, Data Bus +3.3V MLAN HA-A (n8) +48V ON/OFF(1) +48V ON/OFF(1) /RESET (n12) +48V FLASH HA-B 37,40 A[0:18], CS[0] PAD ON/OFF(1:4) PAD ON/OFF(1:4) PAD ON/OFF(1) PNSB PN-A (n8) (8Mbit) /RD, /WR IC110 (8P)
Page 223
DAW AUX R [n12] DAW 5.1 Ls DAW I/O DAW 5.1 Rs n8: 2-REC , 2-REVERB , 2-AUX , 1-EFFECT , 12-FIREWIRE IN/OUT DAW IN [1-16] n8: DAW IN [1-12] FIREWIRE HPF: 100 Hz, -12 dB/Oct n12: 2-REC , 2-REVERB , 2-AUX , 1-EFFECT , 16-FIREWIRE IN/OUT...
Page 224
BLOCK DIAGRAM 004 (n8/n12) n8/n12 Analog Digital Digital Analog Analog Digital Analog INPUT MASTER MASTER GAIN INSERT PHASE COMP LEVEL ROUTING BALANCE (CHANNEL PATCH LEVEL ON/OFF) dBFS Max.Input [+24 dBu] Digital Clipping Level Max.Output [+18 dBu] [+14 dBu] NominalInput [+10 dBu] GAIN MIN.
Page 225
WIRING DIAGRAM (n8) CN103 HA-A MIDI-A : Ferrite Core(フェライトコア) 1-4ch JK-A CN200 CN102 CN101 CN100 CN100 CN102 WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. 安全上の注意 印の部品は、安全を維持するために重要な部品です。 交換する場合は、安全のため必ず指定の部品をご使用ください。...
Page 226
WIRING DIAGRAM (n12) CN103 HA-B HA-A MIDI-B 1-4ch 5-8ch JK-B CN200 : Ferrite Core(フェライトコア) CN102 CN101 CN100 CN102 CN101 CN100 CN104 CN101 CN100 CN102 WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. 安全上の注意...
PN-A/PN-B 001 CIRCUIT DIAGRAM (n8/n12) n8/n12 to Page 19: N8, G11, P2 to DM-A-CN110 (n8) DM-B-CN110 (n12) (Page 9: D3) to PS-CN102 (Page 26: A4) E-PNS2a to Page 19: D2, H6, O5, P1 LED/SWITCH DRIVER to Page 19: C2, F5, P1...
Page 237
PNA/PN-B 002 CIRCUIT DIAGRAM (n8/n12) n8/n12 to Page 18: B4 to Page 18: M4 to Page 18: B4 to Page 18: M4 to Page 18: B1 to Page 18: B4 n12 only to Page 18: M4 to Page 18: B4...
Page 239
PN-A/PN-B 004 CIRCUIT DIAGRAM (n8/n12) n8/n12 n12 only n8 only n12 only n12 only n12 only n8 only n8 only to DM-A-CN101 (n8) to Page 18: G6 DM-B-CN101 (n12) (Page 9: AG9) n12 only n8 only to Page 18: G11...
Page 240
PN-A/PN-B 005, HP-A/HP-B CIRCUIT DIAGRAM (n8/n12) n8/n12 PN-A (n8) (n12) PN-B AUX PHONES HP-A (n8) HP-B (n12) to DM-A-CN113 (n8) C-R PHONES DM-B-CN113 (n12) (Page 10: B7) AUX PHONES to DM-A-CN122 (n8) DM-B-CN122 (n12) (Page 10: B5) C-R PHONES 28CC1-2001012678-5 28CC1-2001012678-6 : Not installed(未実装)...
Page 241
PNSB 001 CIRCUIT DIAGRAM (n12) to DM-B-CN111 (n12) (Page 9: D4) to Page 24: E9, N10 to PS-CN103 (Page 26: A4) E-PNS2a LED/SWITCH DRIVER to Page 25: F3, O2 to Page 24: F5, P2 MA111 (VR496500) 1SS355 TE-17 (VT332900) DTB123YK (VY677700) DTDG14GP T100 (WH175900) DIODE DIODE...
Page 242
PNSB 002 CIRCUIT DIAGRAM (n12) to Page 23: L6 to Page 23: B6 +48V +48V to Page 23: B6 OVER 1 OVER 2 OVER 3 OVER 4 PAD 1 PAD 2 PAD 3 PAD 4 -3 1 -3 2 -3 3 -3 4 80 1 PHASE 1...