Page 1
User Manual HIT-W18 Series Healthcare Infotainment Terminal...
Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 3
Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
Page 4
f. The equipment has obvious signs of breakage. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
Page 5
The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Page 6
Disposing of your old product Within the European Union EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords.
Overview The HIT-W18 Series Patient Infotainment Terminal is a standard product from Advan- tech with Windows XP Embedded OS built-in. In addition to providing hospital bed- side patient information, remote monitoring, and care functions, the CPU and the LAN-enabled architecture of the HIT-W18 Series terminal also serves as an inte- grated hospital gateway device.
Page 11
Note! Power LED: color in green shows power on, no color shows power off Indicator LED: It can show color in orange/green and the definitioni is controlled/defined by customer. HIT-W18 User Manual...
System Configuration The block diagram of a HIT-W18 Healthcare Infotainment Terminal based on Hospital bedside environment is shown in the following diagram: HIT-W18 User Manual...
Chapter Hardware Description This Chapter describes the hard- ware features of the HIT-W18. Sections include: General Specifications Mechanical Specifications External View...
General Specifications 2.1.1 Standard PC Functions Category Specifications Intel PineView (D525) 1.8 GHz SandyBridge (i7) 1.5 GHz Front Side Bus Supports FSB 800 MHz System Chipset Intel D525 + ICH8M/Intel i7 + Cougar Point Memory DDR2 667 200-pin SODIMM x 2 Storage CFAST or SATA HDD interface (Optional) Bus Expansion...
Carton Dimensions: 620 (W) x 540 (H) x 180 (D) (excludes accessories box) Mounting System: Back box for wall mounting Gross Weight: 6.1 kg Net Weight: 6.1 kg VESA Mount: 75*75 mm or 100*100 mm ...
Page 17
Front Cover: Rear Cover: HIT-W18 User Manual...
Chapter Software Description This Chapter describes the soft- ware features of the HIT-W18. Sections include: Windows XP Embedded Soft- ware Specifications...
Windows XP Embedded Software Specifications Real-Time OS Kernel Windows XPE 7 Language Version Driver List Chipset Intel ICH8M Rev. 9.2.0.1025/Chipset Intel CougarPoint QM67 Rev. 9.2.0.1025 Graphics Intel Atom D525 Rev. 6.14.10.5080/Graphics Intel Graphics 200 Rev. 6.14.10.5298 Audio Realtek audio ALC892 Rev.5.10.0.6316 LAN Realtek RTL8111DL Rev.5.728.604.2009 Camera D-MAX 2M AF Camera Rev.
Chapter Design Requirements This Chapter describes the design requirements of the HIT-W18 Series. Sections include Environmental Specifications Reliability...
Environmental Specifications Temperature & Humidity Operating Temperature: 0 ~ 40° C Storage Temperature: 0 ~ 60° C Relative Humidity: 0 ~ 95% RH (Non-condensed) Case / Panel Temperature Less than 40° C @ 25° C ambient temperature (front bezel) Safety ...
Chapter Installation This Chapter describes the instal- lation of the HIT-W18 Series. Sections include Terminal Installation Handset Installation Remote Controller Installation Arm Installation...
Annex Guidance and manufacturer’s declaration – electromagnetic emissions The model HIT-W18 is intended for use in the electromagnetic environment specified below. The customer or the user of the model HIT-W18 should assure that it is used in such an environment. Electromagnetic environment –...
Page 33
Guidance and manufacturer’s declaration – electromagnetic immunity The model HIT-W18 is intended for use in the electromagnetic environment specified below. The customer or the user of the model HIT-W18 should assure that it is used in such an environment. IEC 60601 test Compliance Electromagnetic environ- Immunity test...
Page 34
Guidance and manufacturer’s declaration – electromagnetic immunity The model HIT-W18 is intended for use in the electromagnetic environment specified below. The customer or the user of the model HIT-W18 should assure that it is used in such an environment. IEC 60601 test Compliance Electromagnetic environment –...
Need help?
Do you have a question about the HIT-W18 Series and is the answer not in the manual?
Questions and answers