Hitch Assembly; Sunstar; Sovereign; Landlord - Simplicity Turbo Turbo Wide Body Cart & Hitch Operator's Manual

HITCH INSTALLATION
SunStar/1900 Series (Mfg. No. 1691526)
1. Install the U-bracket (A, Figure 22) with two 1/2-13 x
1 1/4 capscrews (B), 1/2 lockwashers, and nuts. At
top hole on each side, install two 7/16-14 x 1-1/2 cap
screws (C), lockwashers and nuts.
Note: The U-bracket (A, Figure 22) is an accessory hitch
with additional ear for tiller attachment. U-bracket (19,
Figure 1) supplied with cart mounts in same location with
supplied hardware.
2. See Figure 22. Position brackets (D) with large hole
(E) at bottom of each side. In large holes (E), install
5/8-11 x 1-1/4 capscrews, lockwashers and nuts.
3. In top holes of bracket (D), install two 7/16-14 x 1/2
capscrews (F), 7/16 lockwashers and nuts.
Sovereign/900 Series (Mfg. No. 1691526)
Note: Hitch assembly is packaged with the Turbo Blower
Assembly, Mfg. No. 1692257.
1. Assemble the hitch U-bracket (B, Figure 23) to the
support bracket (F) with two 1/2-13 x 1-1/2 cap-
screws (G) and locknuts (A).
2. Install hitch bracket assembly to tractor drawbar and
secure on sides with 1-3/4 clevis pins (D) and spring
clips (1).
Landlord/1700 Series (Mfg. No. 1692526)
1. Assemble the hitch bracket (A, Figure 24) to the hitch
support (B) with two 3/8-16 x 1 capscrews (C) and
locknuts (D).
2. Position the hitch bracket to the top side of the draw-
bar (D) with the hitch support to the backside (F) of
the drawbar. Secure the hitch bracket with two 1/2-13
x 1 1/4 capscrews (G), flat washers (H), and locknuts
(I) and the hitch support with two 3/8-16 x 1 cap-
screws and locknuts.
Figure 22. Sunstar Hitch Installation
A. U-Bracket
B. Capscrew, 1/2-13 x 1-1/4 E. Large Hole
C. Capscrew, 7/16-14 x 1/2 F. Capscrew, 7/16-14 x 1/2
Figure 23. Sovereign Hitch Installation
A. Locknut, 1/2-13
B. U-Bracket
C. Washer, Flat
D. Safety Clip
E. Clevis Pin, 7/16x1-3/4 J. Clevis Pin, 1/2 x 7/8
F
G
C
D
Figure 24. Landlord Hitch Installation
A. Hitch Bracket
B. Hitch Support
C. Capscrew, 3/8-16 x 1
D. Locknut, 3/8-16
9
Hitch Installation
D. Bracket
F. Support Bracket
G.Capscrew, Hex, 1/2-13x1-1/2
H.Spacer
I. Spring Clip
C
G
B
H
A
E. Backside Drawbar
F. Capscrew, 1/2-13 x 1-1/4
G. Flat washer, 1/2
H. Locknut, 1/2-13
D
E