1. Manuals
  2. Brands
  3. Simplicity Manuals
  4. Lawn Mower Accessories
  5. 1694389
  6. Operator's manual

Simplicity 1694389 Operator's Manual

Clean sweep triple catcher
Hide thumbs Also See for 1694389:
Table of Contents

Advertisement

Quick Links

ATTACHMENT
OPERATOR'S
MANUAL
Clean Sweep
Triple Catcher
Clean Sweep Triple Catcher
Mfg. No.
Description
1694390
Hitch & Tube Kit (For Use With Legacy XL / 2000 / 2900)
1694389
Clean Sweep Triple Catcher
1725580
Rev. 01
Rev Date 01/2004
TP 100-3898-01-AT-SMAN

Advertisement

Table of Contents
loading

Related Manuals for Simplicity 1694389

Summary of Contents for Simplicity 1694389

  • Page 1 OPERATOR’S MANUAL Clean Sweep Triple Catcher Clean Sweep Triple Catcher Mfg. No. Description 1694390 Hitch & Tube Kit (For Use With Legacy XL / 2000 / 2900) 1694389 Clean Sweep Triple Catcher 1725580 Rev. 01 Rev Date 01/2004 TP 100-3898-01-AT-SMAN...

  • Page 2: Table Of Contents

    Safety Rules & Information General Warnings...2 Safety Decals ...2 General Operating Information Mowing with the Triple Catcher...3 Recommended Accessories...3 After Operation ...3 Initial Hitch Installation - Models without 3-point Hitch Install Hitch ...4 Initial Hitch Installation - Models with 3-point Hitch Install Hitch ...5 Initial Collector Assembly - All Models Assemble Front &...

  • Page 3: Safety Rules & Information

    Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- in text signifies important cautions or warnings which must be followed.

  • Page 4: Mowing With The Triple Catcher

    MOWING WITH THE CATCHER Always operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging.

  • Page 5: Initial Hitch Installation

    Initial Hitch Installation - Models with out 3-Point Hitch Figure 1. Install Side Brackets A. Side Brackets E. Lockwashers, 1/2 B. Spacers F. Clevis Pins C. Nuts, 1/2-13 G. Safety Clips D. Capscrews, 1/2-13 x 2-1/2 INITIAL HITCH INSTALLATION - MODELS WITHOUT 3-POINT HITCH Install Hitch 1.

  • Page 6: Initial Hitch Installation

    Figure 4. Install Side Brackets A. Tube Assembly & Mounting Hardware B. Clevis Assembly & Mounting Hardware C. Lower Link & Chain Assembly D. Hair Pin E. Clevis Pin INITIAL HITCH INSTALLATION - MODELS WITH 3 POINT HITCH Install Hitch 1.

  • Page 7: Initial Collector Assembly - All Models

    Initial Collector Assembly - All Models Figure 6. Install LH Discharge Back Plate A. Back Plate B. Front Plate C. 5/16-18 Nuts & Lockwashers D. 5/16-18 x 3/4 Carriage Bolts E. 5/16-18 x 1-1/4 Carriage Bolts F. Locknut, 5/16-18 G. 5/16-18 x 1 Capscrew H.

  • Page 8: Assemble Tubes & Deflector

    A. Deflector H. Nut B. Back Plate I. Capscrew, C. Capscrew, 1/4-20 x 1-1/4 5/16-18 x 1 J. Washer, 1/4 D. Socket K. Hook E. Upper Tube L. Locknut, 5/16-18 F. Lower Tube M. Washer, 5/16 G. Rubber Strap Figure 8. Assemble Tubes & Deflector Figure 9.

  • Page 9: Assemble Catcher Bags

    Initial Installation & Assembly Figure 11. Assemble Catcher Bags A. Clip B. Cloth Bag C. 5/16-18 x 3/4 Carriage Bolt D. Hanger Bracket Assemble Catcher Bags See Figure 11. 1. Insert the wire hoop (H) through the cloth bag (B). 2.

  • Page 10: Removing The Grass Catcher

    Figure 15. Remove the Cover A. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip Figure 16. Remove the Bags A. Bags REMOVING THE GRASS CATCHER 1. Remove the hair pin clips (D, Figure 15) and hinge pins (B) and remove the cover (A). 2.

  • Page 11: Reattaching The Grass Catcher

    Removing & Reattaching REATTACHING THE GRASS CATCHER Models with out 3-Point Hitch 1. Set the front and back plate assembly on the pins (Figure 19). 2. Secure with the long hitch pin (C, Figure 19) Models with 3-Point Hitch 1. Set the front and back plate assembly on the clevis pins (Figure 20).

  • Page 12: Storing The Grass Catcher

    Figure 210. Bags A. Bags B. Back Plate 3. Hook the bags (A, Figure 21) on the back plate. 4. Install the catcher cover (A, Figure 22 & 23) and secure with the hinge pins (B) and hair pin clips (D). NOTE: Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened.

  • Page 13: Hardware Identification & Torque Specifications

    Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Carriage Bolt Standard Hardware Sizing When a washer or nut is identified as 1/2”, this is the Nominal size , meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the Nominal size , or body diameter is 1/2 inch;...
  • Page 14 M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.

This manual is also suitable for:

1725580

Table of Contents