Specifications; Router Safety Warnings - Makita 3612 Instruction Manual

ENGLISH
(Original instructions)
1 Stopper pole
2 Fast-feed button
3 Adjusting hex bolt
4 Stopper block
5 Knob
6 Nylon nut
7 Lock lever
8 Hex bolt
9 Switch lever
10 Lock-off button
11 Switch trigger
12 Speed adjusting dial
13 Wrench
14 Shaft lock
15 Chip deflector
16 Workpiece
17 Bit revolving direction

SPECIFICATIONS

Model
Collet chuck capacity ............................................. 12 mm or 1/2"
Plunge capacity ..................................................... 0 – 60 mm
–1
No load speed (min ) ........................................... 22,000
Overall length ........................................................ 297 mm (324 mm with knob)
Base diameter ....................................................... 160 mm
Net weight ............................................................. 5.7 kg
....................................................
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.32 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
6
Explanation of general view
18 View from the top of the tool
19 Feed direction
20 Straight guide
21 Wing bolt (A)
22 Guide holder
23 Fine adjusting screw
24 Wing bolt (B)
25 More than 15 mm (5/8")
26 Wood
27 Templet guide
28 Screw
29 Base plate
30 Lock plate lever
31 Bit
32 Base
33 Templet
34 Distance (X)
3612
/II
General Power Tool Safety Warnings
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
ENE010-1
Save all warnings and instructions for future refer-
ence.

ROUTER SAFETY WARNINGS

ENF002-2
1.
2.
ENF100-1
3.
4.
5.
6.
7.
8.
9.
10. Before using the tool on an actual workpiece, let
35 Outside diameter of the templet
guide
36 Wing bolt (C)
37 Trimmer guide
38 Guide roller
39 Pan head screw
40 Dust cover
41 Collet nut
42 Collet cone
43 Spacer
44 Vaccum head
45 Screws
46 Support
47 Limit mark
48 Brush holder cap
49 Screwdriver
3612C
12 mm or 1/2"
0 – 60 mm
9,000 – 23,000
297 mm (324 mm with knob)
160 mm
5.8 kg
/II
WARNING Read all safety warnings and all
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
GEA010-1
GEB018-4