Subscribe to Our Youtube Channel
Related Manuals for Cumberland Evolution Back-Up
Summary of Contents for Cumberland Evolution Back-Up
- Page 1 Evolution Back-Up Cumberland 1004 E. Illinois St. Assumption, IL 62510 Part No. 4801-5309 Rev 1-15 Owners Manual Evolution Back-Up CUMBERLAND Assumption, IL 62510 • Phone 217-226-4421 • Fax 217-226-4420...
-
Page 2: Table Of Contents
Evolution Back-Up Assembly ........................ 9 11.2 Wiring the Back-Up Board Sensors and Alarm Connections .............. 10 11.3 Evolution Back-Up Power Trak Override Settings and Wiring ............11 11.4 Power Supply Connection ........................12 11.5 Connecting Local Network &... -
Page 3: Ratings And Specifications
When this controller is used in a life support heating and ventilation system where failure could result in loss or injury, the user should provide adequate back-up, or accept the risk of such loss or injury! Part No. 4801-5309 rev 1-15 Evolution Back-Up 3 of 17... -
Page 4: Introduction To The Evolution Back-Up System
3. Introduction to the Evolution Back-Up System The Evolution system has the Display Indicator Main Display option of containing an integrated Back-Up System. This Back-Up System contains 4 stages: 1 Heat and 3 Cool. This system’s ® purpose is to back up the master controller in the case of failure. -
Page 5: Emergency Operation
Back-Up. The jumpers should be placed based on the operation of stage equipment and should be the same as assigned STAGE RELAY BOARD in the EV-3000 Controller. Jumpers are placed according the following table: Part No. 4801-5309 rev 1-15 Evolution Back-Up 5 of 17... -
Page 6: Day-To-Day Back-Up Operating Instructions
Note: It is recommended that the High Limit be at least 10º above the room’s target temperature and that the Low Limit be 10º below the room’s target temperature. Part No. 4801-5309 rev 1-15 Evolution Back-Up 6 of 17... -
Page 7: Program Mode Parameters
+ and - buttons as needed. When you have finished with the current setting, press the “Mode” button to move to the next parameter. The program mode parameters for the Evolution Back-Up are shown in Table 1. -
Page 8: Installation
Standard Screwdriver 10.3 Installation Instructions 1. Hang Evolution Back-Up with four screws and the plastic mounting brackets included. 2. Make sure all power supplies are disconnected before breaking any wires, or reaching into the enclosure. 3. Locate the sensor connections. Refer to Wiring Diagrams, Schematics, etc. -
Page 9: Wiring Diagrams
Wiring Diagrams 11.1 Evolution Back-Up Assembly Tunnel Override Settings Vent Override Settings Backup Connections to Evolution Local Network Connections Voltage Selector Switch Power Supply Connections Alarm Connections Sensor Connections Part No. 4801-5309 rev 1-15 Evolution Back-Up 9 of 17... -
Page 10: Wiring The Back-Up Board Sensors And Alarm Connections
NOTE: Tape Shields to Prevent Damage. Installed – Enabled Vacant – Disabled Inset C Back-Up Alarm Connection Internal Wiring Switch Contacts For a Series For a Parallel Alarm Connection Alarm Connection BACK-UP ALARM Part No. 4801-5309 rev 1-15 Evolution Back-Up 10 of 17... -
Page 11: Evolution Back-Up Power Trak Override Settings And Wiring
11.3 Evolution Back-Up Power Trak Override Settings and Wiring Evolution Back-Up Circuit Board PowerTrak Inset A Vents Override Tunnel Override Inset A Vent Override Inset B PowerTrak Cont Open Vent Override CONTROLLER AC IN SWITCH Open EV-3000 Close NOTE: If curtain is setup to pull curtain up to open, then reverse wires connected to 'Open' and 'Close' terminals. -
Page 12: Power Supply Connection
11.4 Power Supply Connection NOTE: Controllers shipped from HHI set to 240V. Set slide switch of power selector to voltage of power supply connected! Part No. 4801-5309 rev 1-15 Evolution Back-Up 12 of 17... -
Page 13: Connecting Local Network & Back-Up To The Evolution 3000
Harness In Expansion & Backup Warning! Tape Shield To Prevent Damage! NOTE: Harness to connect Local Network and Back-up together are connected & included in the Back-up and 16 Stage Expansion units. Part No. 4801-5309 rev 1-15 Evolution Back-Up 13 of 17... -
Page 14: Temperature Vs. Sensor Resistance Table
57.2 9.007 81.3 27.4 4.82 108.5 42.5 16.312 57.6 14.2 8.891 81.9 27.7 4.763 42.8 16.085 58.1 14.5 8.815 82.2 27.9 4.688 109.8 43.2 15.935 58.5 14.7 8.702 82.8 28.2 Part No. 4801-5309 rev 1-15 Evolution Back-Up 14 of 17... -
Page 15: Error Codes
If your controller is displaying an “E1” or “E2”, etc. the controller has recorded an error. The controller records errors based on sensor reading and the communications links. When any of these errors occur an alarm will be generated. Error Codes for the Evolution Back-Up System Error Code Description... -
Page 16: Warranty
Prior to installation, the end-user has the responsibility to comply with federal, state and local codes which apply to the location and installation of products manufactured or sold by GSI. Part No. 4801-5309 rev 1-15 Evolution Back-Up 16 of 17... - Page 17 Part No. 4801-5309 rev 1-15 Evolution Back-Up 17 of 17...
Need help?
Do you have a question about the Evolution Back-Up and is the answer not in the manual?
Questions and answers