Page 1
2518 Series Operator’s Manual Automatic Parts Washer Top-Load MODELS: 1.043-342.0 1.043-343.0 1.043-344.0 1.043-345.0 1.043-380.0 1.043-381.0 1.043-508.0 Y CU 1- YE Y TO ) PE 2 KG 1 LB nt s X DE pr ov r CU ://w ll 88 S TO...
KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower right corner of the front cover. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
When ordering parts, please specify model and serial number. Use only identical replacement parts. This machine is to be used only by trained operators. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
You must comply with all inflammable avant de les placer à l'intérieur de warnings and wear all protective clothing stated on l'armoire.Le non-respect de cet avertissement the SDS. créera une condition extrêmement dangereuse. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 7
16. After the machine stops, wait 10 seconds before opening the lid or door. This automatic parts washer is designed to operate safely and efficiently. Before you begin to install and use the machine, please familiarize yourself with the major components. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
88 S TO ht tp 90 -D EX TE CL US TE RG (Optional) Lid Handle Power Brush Skimmer (Optional) Assy. Access Panel Debris Tray Sump Drain Collection Container Detail Brush Assembly (Optional) Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 9
Operations Component Identification - Rear Control Panel Steam Vent Electrical Optional Autofill Assy. Drive Motor Assy. Access Panel Sump Pump Power Cord Heating Element/ Thermostat Assy. Low Water Shutoff Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Read 5. Hang the power brush on the bracket mounted and understand the machine identification tag to along the right side of the machine. determine the electrical power requirements before installing the machine. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
5. Close the lid. 6. Turn the heater timer to the 2 hour position. The sump will reach operating temperature (160°- 180°F) in approximately one hour. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Turntable Switch Adjustment The turntable switch is a simple rocker switch that Screw enables you to disconnect power to the turntable motor. Set to ON, the turntable rotates during the wash cycle. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
WARNING: Particles dislodged by the power brush hand detail brush. could cause serious injury to your eyes. Always wear approved eye and hand protection when Position #1 - Power Brush Position #2 - Detail Brush using the power brush. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Float Proximity Switch NOTE: If your machine is equipped with the optional automatic water fill feature, the sump will automatically fill when the water level drops below the lower low water proximity switch. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Top switch CLOSED, Bottom Switch Water Fill Valve (if installed) CLOSED, CLOSED, Automatic Water Fill Valve (if OPEN, Automatic Water Fill Valve (if Heating Element ON. installed) OPEN, Heating Element OFF. installed) OPEN, Heating Element OFF. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
• heat the water to operating temperature; • add detergent if necessary; • verify that none of the spray nozzles are clogged; and clean the debris screen. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
To ensure optimum performance and trouble free oper- ation, observe the following maintenance schedule consistently. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
To remove the debris either flush it out through the sump drain, or vacuum it out using a wet/dry vac. Dispose of the debris in accor- dance with applicable local, state and federal regu- lations. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
3. Taking care not to kink or tangle the chain, place it on the turntable and close the lid. 4. Remove the turntable motor cover (Two 5/16” screws, See Figure On Next Page). Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
5/16” wrench or socket Required Tools and Equipment • 1/2” wrench or deep socket • 5/16” wrench or socket • small phillips-head screwdriver • 1/2” wrench or socket • small flat-head screwdriver • small phillips-head screwdriver Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 21
Wire 7. Reassemble the skimmer and replace it on the Nuts machine. Assembly is the reverse of removal. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
E l e c t r i c a l Pa n e l i s fuses or other electrical components. OK, Refer to Testing Individual Components Pump Fuses Heater Fuses Transformer Ground Terminal Strip Relays Timer Pump Overload Relay Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
If there is continuity the switch is no longer func- tional; replace the switch. 4. With the switch fully closed (depressed), test for continuity. If there is not continuity the switch is no longer functional; replace the switch. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
If there is not continuity the thermostat is no longer If the ohm meter reads approximately 1 ohm, the functional; replace the thermostat. start capacitor is no longer functional; replace the start capacitor. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 25
Check the thermostat to ensure that it is Thermostat is incorrectly installed correctly installed into the mounting bracket (See “Thermostat” Section). WASH SOLUTION IS TOO HOT Replace the thermostat Failed thermostat (See “Thermostat” Section). Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Pump is failed or a customer service representative to test the pump motor. OIL SKIMMER Check electrical panel for a blown fuse; DOES NOT Blown fuse replace if necessary. OPERATE PROPERLY Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 27
10 to 12 scoops (20 to 24 cups) per 50 gallons of Low detergent concentration or MACHINE IS water, contains adequate rust inhibitors to prevent improper detergent usage RUSTING rust. Verify that you are using our detergents at the correct concentration. Cuda 2518 Operator’s Manual 8.915-630.0 - AM...
Page 28
Notes Cuda 2518 Operator’s Manual 8.915-630.0 - AM...