Page 1
1.043-528.0 1.043-529.0 1.043-530.0 1.043-531.0 1.043-532.0 1.043-534.0 1.043-539.0 For the Cuda Dealer nearest you, consult our web page at WARNING: www.CudaUSA.com This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm.
KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower right corner of the front cover. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
When ordering parts, please specify model and serial number. Use only identical replacement parts. This machine is to be used only by trained operators. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
8. Use caution when lifting items in and out of parts pourraient survenir. basket to prevent back injuries. KEEP WATER SPRAY AWAY FROM 2.All installations must comply ELECTRICAL WIRING. with local codes. Contact your Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Page 7
16. After the machine stops, wait 10 seconds before opening the lid or door. This automatic parts washer is designed to operate safely and efficiently. Before you begin to install and use the machine, please familiarize yourself with the major components. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Operations Component Identification - Front Control Panel Top Spray Assembly Side Spray Arm Assembly Flow Regulator Turntable Assembly Chain Guard Detail Brush (Optional) Pump Power Brush (Optional) Debris Screen Tank Drain Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
To connect the machine to your shop water supply, install a 1/2"NPT (male) by 5/8" (female) connection to the water supply inlet valve, then connect to a nearby water spigot using a suitable burst-proof hose. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
When set between 1 and 60 minutes, the timer automatically shuts off the pump and turntable when the wash cycle is complete. When set to Hold (220V Only), the pump and turntable run continuously until manually shut off. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Decrease washed through from the cleaning chamber. Temperatures Standard Screen: 10 Mesh Optional Screen: 60 Mesh Debris Screen Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Both Switches OPEN, Automatic OPEN, Automatic Water Fill Valve (if Water Fill Valve (if installed) CLOSED, Automatic Water Fill Valve (if installed) OPEN, Heating Element OFF. installed) OPEN, Heating Element Off. CLOSED, Heating Element ON. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Refer to Connect a Compressed-Air Line and Accessories detailed installation information. NOTE: The power brush is a standard component on the Deluxe Edition. It is available as an option on the base model. For ordering information, contact your dealer. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Detail container. The gear motor is controlled by a rocker Brush switch on the control panel. See information in Maintenance Section for detailed operati Skimmer Assembly Container Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Follow recom- mended detergent quantities. Use pH kit to determine the proper amount of detergent to use. If you need help interpreting test results, contact customer service. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
4. When the machine automatically stops (or after you manually stop the wash cycle), lift the lid and wait a few moments to allow the parts to cool and dry before removing them. Most parts flash-dry in seconds. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
NOTE: The spray nozzles are sized and positioned to optimize the distribution of cleaning solution in the c. Pull up evenly on the turntable to remove it from wash chamber. If you remove the nozzles make sure the center pin. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
1. Allow the machine to sit idle for at least 30 minutes Rotate to allow the oil to float to the surface of the wash Clockwise solution. Rotate Turntable Clockwise Until Chain Reaches Completely Around Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
6. Allow the thermostat to cool to room temperature, then test for continuity. Power If there is not continuity the thermostat is no longer Leads functional; replace the thermostat. Heating Element Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
9. Use a 1/8" hex key to remove the pulley and steam shield disk from the drive motor shaft, then remove the four screws holding the motor to the mounting bracket. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
11. Remove the impeller from the shaft. 12. Using a flat-head screwdriver, carefully remove first the rotary seal head, then the ceramic stationary Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
1. Disconnect power to the machine. 2. Loosen the compression fitting on the back of the lid to allow enough slack in the wires to access the rear of the control panel when you remove it. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
34-35 to eliminate the Individual Components possibility of a blown relay or a bad connection, then refer to Testing Individual Components to determine which component is causing the problem. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Page 25
Blown; Replace the of Each Blown Fuse approximately 0 Ohms E l e c t r i c a l Pa n e l i s OK, Refer to Testing Individual Components Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
4. With the timer in the ON position, test for continuity thermostat enclosure (Two Screws; Use a 5/16" using an ohm meter. Wrench or Socket). 5. If there is not continuity the timer is no longer func- tional; replace the timer. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Bracket Thermostat 5. Set the thermostat to 120 °F, warm it to just above 120 °F, then test for continuity. If there is continuity the thermostat is no longer functional; replace the thermostat. Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Use a water softener and/or change your sump water POWDER dissolved solids) more frequently. ON PARTS Large parts can dry before solution Turn heat down to approximately 140° runs off, leaving powdery residue Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Page 29
MACHINE IS RUSTING Steam condensing on inside of Leave lid open during long idle periods. cabinet and lid PUMP Failed pump seal Replace the pump seal, see Pump Seal. LEAKS Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
Page 30
Notes Cuda 2216 Operator’s Manual 8.941-287.0 - AE...
31 32 48, 49, 50 SIDE NOZZLES 3° TOP & BOTTOM NOZZLES Rotate Each Nozzle Approximately 3° Align The Notch In Each From The Center Line Spray Nozzle With The Of The Pipe Turntable Cuda 2216 Operator’s Manual 8.941-287.0 - AE...