Hunter Douglas PowerView Motorization Manual page 20

U.S. Radio Frequency FCC Compliance
This device complies with P art 15 of the F C C R ules. O peration is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a C lass B digital device, pursuant to P art 15 of the F C C R ules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• R eorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• C onnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• C onsult the dealer or an experienced radio/TV technician for help.
Any changes or modi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Industry Canada
Under Industry C anada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry C anada. T o reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry C anada licence-exempt R SS standard(s). O peration is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Class B Digital Device Notice
This C lass B digital apparatus complies with C anadian IC E S-003, R SS-G en and R SS-210.
Industrie Canada
C onformément à la réglementation d'Industrie C anada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émetteur par Industrie C anada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs,
il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux C NR d'Industrie C anada applicables aux appareils radio exempts de licence. L 'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
Appareil Numérique de Classe B – Avis
C et appareil numérique de classe B est conforme à la norme NMB-003, C NR -G en et C NR -210 du C anada.
C AN IC E S-3 (B)/NMB-3(B)
European Conformity
We, the undersigned,
Hunter Douglas Window F ashions
O ne Duette Way, Broom eld, C O 80020, USA
Hunter Douglas E urope B.V .
P iekstraat 2, 3071 E L R otterdam, The Netherlands
certify and declare under our sole responsibility that the P owerView ® R emote C ontrol conforms with the essential requirements of the E MC directive
2004/108/E C and R &TTE directive 1999/5/E C .
A copy of the original declaration of conformity may be found at www.hunterdouglas.com/RFcerti cations.
3 7