Proce 4.Dure 4. 3 - Add / Modify Se 4.Rvice 4. Use 4.R Acce 4.Ss Code 4; Proce 4.Dure 4. 4 - De 4.Le 4.Te 4. Use 4.R Acce 4.Ss Code 4.S - Kaba E-Plex 50 Series Operation Manual

PROCEDURE 3 - ADD / MODIFY SERVICE USER
A Se 4.rvice 4. Use 4.r is any pe 4.rson who ne 4.e 4.ds acce 4.ss to the 4. lock for a limite 4.d time 4.
pe 4.riod in orde 4.r to pe 4.rform a se 4.rvice 4., such as painting or re 4.pairs in the 4. room or
are 4.a . A Se 4.rvice 4. Use 4.r Acce 4.ss Code 4. allows the 4. se 4.rvice 4. pe 4.rson to e 4.nte 4.r, e 4.xit and
re 4.-e 4.nte 4.r using that code 4. for a ce 4.rtain numbe 4.r of hours, up to a maximum of 24
hours .
Required User Level: Master, Manager
1 . Put the 4. lock into Pushbutton Programming Mode 4. .
2 . Ente 4.r Command 102# to add / modify a Se 4.rvice 4. Use 4.r Acce 4.ss Code 4. .
3 . Ente 4.r the 4. Se 4.rvice 4. Use 4.r ID location (a thre 4.e 4.-digit numbe 4.r you have 4. on a list
that you should carry with you) followe 4.d by #, for e 4.xample 4. 025# .
4 . Ente 4.r UUUUUUUU#, re 4.pre 4.se 4.nting a Use 4.r Acce 4.ss Code 4. of be 4.twe 4.e 4.n 4 and
8 numbe 4.rs de 4.pe 4.nding on the 4. le 4.ngth of Acce 4.ss Code 4. that you se 4.le 4.cte 4.d in
Proce 4.dure 4. 1 on page 4. 7 . For e 4.xample 4., if your code 4. le 4.ngth is 4 digits, it could
be 4. 2240# .
5 . Ente 4.r the 4. code 4. 2240# again .
6 . Now e 4.nte 4.r the 4. numbe 4.r of hours, programmable 4. be 4.twe 4.e 4.n 01 and 24, for
e 4.xample 4. 04 . If you e 4.nte 4.r a Se 4.rvice 4. Acce 4.ss Code 4. of 00, you can only
e 4.nte 4.r the 4. door once 4. . If the 4. door shuts upon e 4.xiting, you will not be 4. able 4.
to re 4.-e 4.nte 4.r . This type 4. of acce 4.ss is calle 4.d a one 4.-shot code 4. .
7 . Example 4. of Comple 4.te 4. Entry: 102#025#2240#2240#04# .
8 . Ente 4.r anothe 4.r # to indicate 4. the 4. e 4.nd of programming .
9 . The 4. Se 4.rvice 4. Use 4.r Acce 4.ss Code 4. 2240 will now work in that door, for this
Se 4.rvice 4. Use 4.r for a pe 4.riod of 4 hours from the 4. time 4. the 4. Se 4.rvice 4. Use 4.r
e 4.nte 4.rs his Acce 4.ss Code 4. the 4. first time 4. .
PROCEDURE 4 - DELETE USER ACCESS CODES
Use 4.r Acce 4.ss Code 4.s should be 4. de 4.le 4.te 4.d from the 4. lock if no longe 4.r ne 4.e 4.de 4.d . This
fre 4.e 4.s the 4. Use 4.r ID location to be 4. assigne 4.d to anothe 4.r use 4.r . Code 4.s that may be 4.
ne 4.e 4.de 4.d some 4. time 4. in the 4. future 4. should be 4. de 4.-activate 4.d rathe 4.r than de 4.le 4.te 4.d .
Required User Level: Master, Manager
1 . Put the 4. lock into Pushbutton Programming Mode 4. .
2 . Ente 4.r Command 200# to de 4.le 4.te 4. a Use 4.r Acce 4.ss Code 4. .
3 . Ente 4.r the 4. Use 4.r ID location NNN#, whe 4.re 4. NNN is the 4. spe 4.cific Use 4.r ID
location from 000 to 299 .
4 . Example 4. of comple 4.te 4. e 4.ntry: 200 #023# .
5 . Ente 4.r anothe 4.r # to indicate 4. the 4. e 4.nd of programming .
By de 4.le 4.ting a Use 4.r ID location, you have 4. now also de 4.le 4.te 4.d the 4. associate 4.d Use 4.r
Acce 4.ss Code 4., allowing you to assign this Use 4.r ID location with a ne 4.w acce 4.ss
code 4. to anothe 4.r use 4.r if you wish .
ACCESS CODE
17