Table of Contents
Advertisement
Quick Links
Portable Submersible Pump
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Manual Index
INSTALLATION MANUAL
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
70 Series
0.7 HP, 120 Volt
0.7 HP, 240 Volt
125 Series
1.25 HP, 120 Volt
1.25 HP, 240 Volt
Form No. 115150-Rev. J
Advertisement
Table of Contents
Related Manuals for Barnes 70 Series
Summary of Contents for Barnes 70 Series
- Page 1 Manual Index INSTALLATION MANUAL Portable Submersible Pump 70 Series 0.7 HP, 120 Volt 0.7 HP, 240 Volt 125 Series 1.25 HP, 120 Volt 1.25 HP, 240 Volt IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur.
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Prosser and ® Barnes are registered trademarks of Crane Pumps & Systems, Inc. 2003, 10/04, 5/06, 9/06 Alteration Rights Reserved... -
Page 3: Pump Specifications
25 Ft (7.6m) Ceramic, Motor End STRAINER ......25” (6mm) Openings, Non-Metallic Rotating Face ...Carbon LIFTING HANDLE ....Non-Matallic Elastomer ..Buna-N Hardware ..300 series stainless steel MODEL NO. BARNES PROSSER A - Dim VOLT HERTZ FULL LOAD PART NO. PART NO. -
Page 4: Section B: General Information
DO NOT USE THE POWER CABLE TO LIFT PUMP. B-4) Service Centers: For the location of the nearest Barnes or Prosser Center, C-4.2) Overload Protection: check your Barnes or Prosser representative or An automatic thermal overload protects the motor. The Crane Pumps &... - Page 5 It will then automatically reset and restart the pump after E-4) Fasteners: the motor cools to a safe temperature. In the event of an All bolts, nuts, screws and other means of fastenings shall overload, the source of this condition should be deter- be in place, properly tightened and secured.
- Page 6 SECTION G - WARRANTY REPAIR AND TABLE 1 - COOLING OIL - Dielectric REPLACEMENT PARTS SUPPLIER GRADE Shell Turbo oil 32 G-1) Information Needed: Texaco Rando HD32 Always furnish the following information: Mobile D.T.E. Oil Light 1. Pump Part Number G &...
-
Page 7: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 8 Figure 2...
-
Page 9: Parts List
PARTS LIST ITEM PART NO. DESCRIPTION 115084 SkHd Screw, M6 x 15, SS 115085 Flatwasher, 6mm, SS 115083 Discharge Outlet, 2” NPT 115086 Discharge Gasket 115081 Cable Clamp 115082 Self-Tapping Screw M4.8 x 16, SS 115078 Cable, w/Plug 120 Volt 115079 Cable w/o Plug 240 Volt 115131... - Page 10 Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you speci• c legal rights, and there may also be other rights which vary from state to state.
-
Page 11: Returned Goods
IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. To complete the Warranty Registration Form go to: http://www.cranepumps.com/ProductRegistration/ If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. - Page 12 Notes...