Related Manuals for Concox GT03C
Summary of Contents for Concox GT03C
-
Page 1: User Manual
GPS Vehicle tracker User manual (Version V2.0) Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only. - Page 2 1 Accessories Please check whether these accessories are included. Pictures are for indication and illustration purposes only.
- Page 3 2 Appearance 2.1 LED status (non‐sleep mode) 2.1.1Red LED (Power/working status) LED Status Indication Flash quickly (interval 0.1S) Low battery Flash slowly (interval 2s) Full charge/Working normally Flash slowly (Flash 0.1s after every 2s) Working normally Bright Charging Dark Out of battery / Troubleshot 2.1.2 Blue LED（GPS signal status）...
-
Page 4: Operation
Bright Incoming/outgoing calls No GSM signal or no SIM card Dark installed 2.1.4 Defense Status Indication While the three LEDs (blue/red/green) flash cyclically, it means the device begins to enter defense status. Note: 1. When it runs with battery, after GPS being located over 5s, all LEDs will be automatically turned off. -
Page 5: Device Installation
(4) The device can work normally during charging. Red LED being light indicates that it is charging. When charging is finished, red LED will flash slowly. Warning: the ambient temperature shall be 0℃～40℃ while charging. Please use the charger provided by the manufacturer. 3.4 Device installation The device has a strong magnet in rear cover which could attach to any mental surface. -
Page 6: Sos Numbers Setting
4 Functions and Parameter Settings 4.1 APN Setting Please send SMS command to the number of device so as to set up the APN parameter. The device will reply “OK” automatically after setting successfully. The SMS command is as follows: APN,APN’s name# APN,internet# Note: The APN of some countries have user name and password, you may need to send SMS command as following:... - Page 7 4.2.3 Add SOS number via platform You can set SOS numbers via the platform when the device connects to the platform. Note: Only the SOS number can make the operation as remote defense, monitoring and SMS checking position. 4.3 Arm/disarm There are 3 methods to activate/deactivate defense status.
-
Page 8: Anti-Theft Alarm
4.4 Anti‐theft alarm In defense status, once there is a vibration, the device will send alarm SMS to the SOS numbers in 10s. If the device is located, it will send accurate GPS location to SOS numbers. Otherwise, it will send LBS location first. - Page 9 e.g. FENCE,ON,0,N22.57139,E113.87710,5# It means the radius is 500 meters（radius 1=100M，2=200M····and so on） The device will reply “OK” if set successfully. As long as the device goes in or out of this circular area, it will send alarm to the SOS numbers. You can also set current location coordinates as the centre of the circular fence, “FENCE,ON,0,0,0,radius#”...
- Page 10 upper left corner, the latitude of lower right corner, the longitude of lower right corner, IN#”. E.g. FENCE,ON,1,N22.541183,E113.916,N22.557743,E113.892334,IN# The terminal will reply “OK” if set successfully. Any time the terminal enters this rectangle fence, it will send alarm message to the preset SOS numbers. ...
-
Page 11: Low Battery Alarm
4.6 Low battery alarm When battery is low, device will send low battery alarm SMS to SOS numbers Low battery alarm SMS: “Warning! Battery is low, please charge in time!” When battery is too low, it will send SMS: “Warning! Battery is too low, power off automatically.” 4.7 Voice monitoring Any SOS number calls the device and keep ringing for more than 10s, the device will enter voice monitoring status. -
Page 12: Reboot Setting
4.8.3 Position query via platform The device will send position information to the platform server timely. The user can check the position on the platform. The platform website: www.gpsyeah.com. Please contact your dealer for the login methods and operations. LBS are a rough locating way. For more accurate information, GPS locating function must be activated. -
Page 13: Mode3: Locating According To Command
LBS location. In this mode, if the terminal does not detect any vibration, GPS will be off. And after it detects vibration, it will start working again. Send SMS command: mode,2# 5.3 Mode3: Locating according to command In this mode, the terminal will be in Deep Sleep mode. It will not connect with the platform. You can send SMS command/call to activate checking location function. - Page 14 Change to a place with good Bad reception Near the tall building or in the basement signal The terminal can not No battery power Change a new battery switch on No preset SOS numbers Set SOS numbers make voice monitoring SIM card is without Caller ID function Activate the function SIM card is not inserted correctly...
- Page 15 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.