Advertisement
Quick Links
GPS Vehicle tracker
(GPS+GSM+SMS/GPRS)
GT02N User Manual
(Version 2.1)
Thank you for purchasing the tracker. This manual shows how to operate
the device smoothly and correctly. Please make sure to read this manual
carefully before using this product. Please note that specification and
information are subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer
assumes no responsibility for any errors or omissions in this document.
Advertisement
Related Manuals for Concox GT02N
Summary of Contents for Concox GT02N
- Page 1 GPS Vehicle tracker (GPS+GSM+SMS/GPRS) GT02N User Manual (Version 2.1) Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Please make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.
- Page 2 1. Summary Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet. Overview of the characteristics: 1.GSM 850/900/1800/1900MHZ. 2.GPS position. 3.Auto set APN. 4.180Mah Battery inside, Power-Cut alarm. 5.Motion detect, save GPRS flow and power.
- Page 3 2．Accessories： Power line: Relay: Microphone: SOS line: Manual 3. Specs 1）.GSM：850/900/1800/1900MHZ 2）.GPRS: Class12, TCP/IP 3）.Working Voltage：10V-40V DC 4）.Working current：≈22mA (12VDC) 5）.Working current：≈12mA (24VDC) 6）.GPS locating time：Cold start≈38s（Open sky） Warm start≈32s Hot start≈2s（Open sky） 7）.GPS Precision：10m（2D RM） 8）.Working temperature：-20℃～+70℃ 9）.Working humidity：20%～80%RH 10）.Measurement：97（L）×50（W）×15（H）mm...
- Page 4 4. Wire defined The 2pins orange plug connect with SOS line The 2pins blue and green plug connect with microphone. The 4pins plug connect with power line. For 4pins power line: The red wire connect with power DC12V+ The black wire connect with power DC12V- The white wire from tracker connect with yellow line from relay,the white line from relay connect with power DC12V+.
- Page 5 and accessories. If the model is wrong or the accessories not complete, please contact the dealer. 6.12 Choose SIM card. Please insert a SIM card which support GSM 2G network to the device. Please take dealer’s advice as reference. 6.13 SIM card installation. Discharge the cover of the device and uncover the SIM card holder.
- Page 6 2) Avoid being placed with signal radiators like reverse sensor ； 3) The device has GSM antenna and GPS antenna inside. Please ensure the receiving side of the device is face up and without metal cover. Note: The metal cover will lessen the receiving of GPS signals.
- Page 7 8.The Device Working 8.1 Power on: Connecting to the power. Then the three LED indicators will light. The device will upload the data to the online platform (the default interval of uploading data is 15seconds). When the car is in static state for a long time, the device will be in energy saving mode.
- Page 8 D02# D02# 1)Center number can control the oil and power and resume factory settings 2) Center number can receive the call and text of vibration alarm and over speeding Command alarm. Description 3) SIM must display the income call number to control oil and power.
- Page 9 Feedback Admin2: 3)Authorized Number Set Text Parameter Sample command Authorized 101# number # 1：101#13800138000# 102# number # 2：102#12345678912# 103# number # 3：103#12345678912# Authorized D11# D11# D12# D12# D13# D13# Command 1) Authorization number for SMS control Description oil. 2) Only three numbers to set the authorization number 3) Change the authorization number needs to delete the previous number...
- Page 10 Text Parameter Sample command View C10# C10# authorized Command This directive is used to view the Description equipment authorization number Command Successful Setting： Authorization 1： Feedback Authorization 2： Authorization 3： 5)APN Setting Text Parameter Sample command 802#APN#username#passw 1：802#intenet#123#123# APN Setting ord# 2: 802#internet# APN differs according to the local telecom...
- Page 11 Feedback Server Text Parameter Sample command 1.803#www.18gps.net#7018# SERVER 803#SERVER#port# Parameter 803#58.61.154.247#7018# View SERVER CIP# 1）CIP# Change the IP and port when move to a new Command server Description port：10~65535 Command Successful Setting：set IP OK! Feedback 7)Moving Time Interval Text Parameter Sample command TIMEER...
- Page 12 setting Scope ： 0 ， 10~60 seconds ； 0,no data Command uploading； Description 10~60,means time interval ； the default value is 15 seconds. Command Successful Setting：SET TIMER OK！ Feedback 8)Static Time Interval Text Parameter Sample command STATIC SUP#time interval# SUP#5# Command Scope：1~60 minutes；...
- Page 13 This command is used to cancel sending data Command to the platform Description If need again to restore the uploading, need to send TIMEER Parameter setting. Command SET OK！ Feedback 10)Oil-Cut Text Parameter Sample command RELAY 222# Cut off oil and 222# Parameter1 power...
- Page 14 off the oil or the power when the speed below 20KM/H. Successful Setting：Fuel cut has already Feedback been completed OK! 11)GMT Text Parameter Sample command 801#E8# 801#location time Zone# 801#W4# The default time zone is Beijing time. Command please operate according to the above Description command.
- Page 15 Alarm VIBRATION 123#sensitivity#alarming Parameter way# 123#2#3# Set into V123#2# vibration V123#2# alarm time V123#1# Cancel vibration 456# 456# alarm The sensitivity value of the vibration is from 1 to 5，1is the most sensitive and o is close. Alarming ways: 1, Command calling 2, texting, 3 Calling and Description...
- Page 16 Text Parameter Sample command SSA#speed#alarm 1) SSA#120# way# SPEEDING 2) SSA#150#3# Parameter 1) 667#120# 667#speed#alarm way# 2) 667#150#3# The speed scope is form 60-220, if the speed isnot in this cope, the alarm is off. Command Alarming ：1. calling, 2. texting, Description 3.calling and texting.
- Page 17 Close ACC 840#0# ALARM 15)Reset Text Parameter Sample command RESET 930# 930# Command Reset the device Description Feedback Successful Setting：Reset system, ok! 16)Factory Text Parameter Sample command Parameter 940# 940# Restore the factory setting Only center number can initial this Description function Factory setting will recover to the...
- Page 18 17)Language Setting command Parameter Sample LANG LANG1# LANG1# 1:CHINESE， Parameter LANG0# LANG0#：ENGLISH When check the location, it will reply the Command Chinese location Chinese language Description setting; while reply the URL link when in English language setting. Feedback Successful Setting：SET LANG OK！ GEO-fence Setting Text Parameter...
- Page 19 Set Enclosure-2 OK / Cancel Enclosure OK Feedback 19)Position Text Parameter Sample command command 988# 988# Command Check the longitude and altitude Description other information of the device Command Reply with longitude and altitude, speed Feedback and IMEL. 20)Google Link Text Parameter Sample...
- Page 20 21)Version Text Parameter Sample command VERSION V00# V00# Command The command is to check the software Description version Command VERSION:Xxxx Feedback BUILD:2012-07-05 10:12 22)Param Check Text Parameter Sample command PARAM 886# 886# Command The command is to check the settings and Description the default parameter.
- Page 21 CENTER: center number LANG: language(CN/EN) GMT: time zone (E/W8) 23)Status Check Text Parameter Sample command STATUS 902# 902# Command The command is designed for checking the Description device’s working status. External power:ON/OFF GSM Signal:HIGH/MIDDLE/LOW Command GPS:FIXED/UNFIXED Feedback RELAYER:DISABLE/ENABLE Vibrate Warning:ON/OFF 24)Monitor(Voice Surveillance)-CALL BACK(default) command Parameter...
- Page 22 will call back to admin number. Monitor (Voice Surveillance)-CALL command Parameter Sample Open Calling mode SS1# SS1# Return Call SS0# SS0# back 26)Wire-cut Alarm; Low Battery Alarm command Parameter Sample Disable 555# 555# Enable 666# 666# 9.2 Platform Website: http://www.18gps.net Please click English to change to English language.
- Page 23 APP: Please search MYGNSS in Google store or Apple store. And choose server as 18GPS In production, IP, port have been written in, normally the tracker will be auto online, if the tracker offline, Please set APN by SMS command. Please get APN from sim card inserted mobile operator.
- Page 24 10.1.1 First, please check the three LED working state. If possible. You can call the device’s number to check. If not connected, the device is out of signal. If ● the GSM signals cannot reach your location, please drive to the open sky. ⚫...
- Page 25 10.3 When the device cannot receive the GSM signal, please check the SIM card installation. If the GSM signals cannot reach your location (such as the basement), please drive to the open sky.