Advertisement
Quick Links
GPS Vehicle tracker
(GPS+GSM+SMS/GPRS)
GT06N User Manual
(Version 2.1)
Thank you for purchasing the tracker. This manual shows how to operate
the device smoothly and correctly. Please make sure to read this manual
carefully before using this product. Please note that specification and
information are subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer
assumes no responsibility for any errors or omissions in this document.
Advertisement
Related Manuals for Concox GT06N
Summary of Contents for Concox GT06N
- Page 1 GPS Vehicle tracker (GPS+GSM+SMS/GPRS) GT06N User Manual (Version 2.1) Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Please make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.
- Page 2 1. Summary Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet. Overview of the characteristics: 1.GSM 850/900/1800/1900MHZ. 2.GPS position. 3.Auto set APN. 4.200Mah Battery inside, Power-Cut alarm. 5.Motion detect, save GPRS flow and power.
- Page 3 2．Accessories： Power line: Relay: Microphone: SOS line: Manual 3. Specs 1）.GSM：850/900/1800/1900MHZ 2）.GPRS: Class12, TCP/IP 3）.Working Voltage：10V-40V DC 4）.Working current：≈22mA (12VDC) 5）.Working current：≈12mA (24VDC) 6）.GPS locating time：Cold start≈38s（Open sky） Warm start≈32s Hot start≈2s（Open sky） 7）.GPS Precision：10m（2D RM） 8）.Working temperature：-20℃～+70℃ 9）.Working humidity：20%～80%RH...
- Page 4 10）.Measurement：97（L）×50（W）×15（H）mm 4. Wire defined 5.Device status indicators 5.1 Connect DC 10-40V power supply, push the switch (switch beside the SIM card holder), the red LED will light continuously. 5.2 The blue LED light continuously when searching the GPS signal. Once GPS fixed, the blue LED will be flashing. 5.3 The intermediate green LED (GSM signal state) GSM signal is normal, green LED flashing.
- Page 5 6.13 SIM card installation. Discharge the cover of the device and uncover the SIM card holder. Then insert the SIM card and cover SIM card holder (as follows). 6.14 Open the cover, Push the switch. Then Put back the front cover. 6.15 Connect the device to the 10V-40V power supply.
- Page 6 sensor ； 3) The device has GSM antenna and GPS antenna inside. Please ensure the receiving side of the device is face up and without metal cover. Note: The metal cover will lessen the receiving of GPS signals. 7. Device wiring requirements 7.1 The device power supply is DC 10V-40V.
- Page 7 energy saving mode. 8.2 Power off：Pull off the power plug then power off the device. 9.User Settings 9.1 SMS Commands instruction 1)Center Number Text Parameter Sample command 710#number# 710#13500135000# CENTER Add 711#number# 711#13800138000# D01# D01# CENTER Del D02# D02# 1)Center number can control the oil and power and resume factory settings 2) Center number can receive the call and text of vibration alarm and over speeding...
- Page 8 Command Successful Setting： Add admin account 1 OK! Feedback 2) View Center Number Text Parameter Sample command View 901# 901# Command This directive is used to view Device Description Manager number. Command Successful Setting：Admin1: Feedback Admin2: 3)Authorized Number Set Text Parameter Sample command...
- Page 9 Command 1) Authorization number for SMS control Description oil. 2) Only three numbers to set the authorization number 3) Change the authorization number needs to delete the previous number Add Authorization Command Successful Setting： account 1 OK! Feedback View Authorized Number Text Parameter Sample...
- Page 10 5)APN Setting Text Parameter Sample command 802#APN#username#passw 1：802#intenet#123#123# APN Setting ord# 2: 802#internet# APN differs according to the local telecom Command operators. Description For example：APN request password，please refer to Sample 1，and Sample 2 for no password. Command Successful Setting：SET APN OK！ Feedback Server Text...
- Page 11 port：10~65535 Command Successful Setting：set IP OK! Feedback 7)Moving Time Interval Text Parameter Sample command TIMEER Parameter 730#20# 730#upload interval# setting Scope ： 0 ， 10~60 seconds ； 0,no data Command uploading； Description 10~60,means time interval ； the default value is 15 seconds. Command Successful Setting：SET TIMER OK！...
- Page 12 STATIC SUP#5# SUP#time interval# Command Scope：1~60 minutes； Description The default time interval is 5 minutes. Command Successful Setting：SET STATIC TIME OK！ Feedback Cancel the continuous upload Text Parameter Sample command NUP# NUP# This command is used to cancel sending data Command to the platform Description...
- Page 13 Parameter1 power RELAY 333# 333# Parameter2 Recover oil and power 1)RELAY control the start and closeness of the relay 2) Only the center number can operate. 3）The device only cut off the oil circuit on the condition of the driving speed below Command 20KM/H or in static state.
- Page 14 Description please operate according to the above command. Command Successful Setting：Set time zone ok! Feedback 12)Vibration Alarm Text command Parameter Sample Open Vibration 911# 911# Alarm VIBRATION 123#sensitivity#alarming Parameter way# 123#2#3# Set into V123#2# vibration V123#2# alarm time V123#1# Cancel vibration 456# 456#...
- Page 15 calling 2, texting, 3 Calling and texting. Need set the center number and receiving number. Command Set vibration alarm level，OK! Feedback 13)Speed Alarm Text Parameter Sample command SSA#speed#alarm 1) SSA#120# way# SPEEDING 2) SSA#150#3# Parameter 1) 667#120# 667#speed#alarm way# 2) 667#150#3# The speed scope is form 60-220, if the speed isnot in this cope, the alarm is off.
- Page 16 Command Successful Setting：set speeding alarm，OK! Feedback 14)ACC Alarm Text Parameter Sample command Open ACC 840#1# 840#1# Alarm Close ACC 840#0# ALARM 15)Reset Text Parameter Sample command RESET 930# 930# Command Reset the device Description Feedback Successful Setting：Reset system, ok! 16)Factory Text Parameter Sample...
- Page 17 command Parameter 940# 940# Restore the factory setting Only center number can initial this Description function Factory setting will recover to the original setting Feedback Successful Setting：FACTORY OK！ 17)Language Setting command Parameter Sample LANG LANG1# LANG1# 1:CHINESE， Parameter LANG0# LANG0#：ENGLISH When check the location, it will reply the Command Chinese...
- Page 18 command Setting 920#radius#way# 920#1#2# Cancel 921# 921# Setting Geo-fence alarm, radius from 1- 100, Unit: 100 meter. Command Alarming ：1, calling 2, texting Description Geo-fence time, Geo-fence canceled. Set Enclosure-2 OK / Cancel Enclosure OK Feedback 19)Position Text Parameter Sample command command 988#...
- Page 19 command command 666# 666# Command Descripti Check the location link of Google map <Datetime:12-07-05 13:21:30> Command http://maps.google.com/maps?q=N22.540885,E113. Feedback 95265 21)Version Text Parameter Sample command VERSION V00# V00# Command The command is to check the software Description version Command VERSION:Xxxx Feedback BUILD:2012-07-05 10:12 22)Param Check Text...
- Page 20 PARAM 886# 886# Command The command is to check the settings and Description the default parameter. IMEI:351190012535936 APN : cmnet IP:IP and port Command TIMER: moving uploading interval Feedback STATIC: static uploading interval CENTER: center number LANG: language(CN/EN) GMT: time zone (E/W8) 23)Status Check Text Parameter...
- Page 21 RELAYER:DISABLE/ENABLE Vibrate Warning:ON/OFF 24)Monitor(Voice Surveillance)-CALL BACK(default) command Parameter Sample SSS# SSS# SSS# Using Command Send this command to Description the tracker’s number, the tracker will call back to admin number. Monitor (Voice Surveillance)-CALL command Parameter Sample Open Calling mode SS1# SS1# Return Call...
- Page 22 9.2 Platform Website: http://www.18gps.net Please click English to change to English language. Login as Account or IMEI,IMEI is in the label on the tracker. Enter IMEI The default Password:123456 APP: Please search MYGNSS in Google store or Apple store. And choose server as 18GPS In production, IP, port have been written in, normally the tracker will be auto online, if the tracker offline, Please set APN by SMS command.
- Page 23 If you lost IP, port, please send below SMS command by admin number to set them back： 803#58.61.154.247#7018# 10.Trouble shooting 10.1 The device is not online or offline on the web platform. 10.1.1 First, please check the three LED working state. If possible.
- Page 24 10.1.2 Please check the offline area in order to judge if the network problem of operators. 10.2 When GPS cannot receive the signals, please drive in the open sky and ensure there is no metal thins on the device. 10.3 When the device cannot receive the GSM signal, please check the SIM card installation.