Related Manuals for Concox GT06N
Summary of Contents for Concox GT06N
-
Page 1: User Manual
GPS Vehicle tracker (GPS+GSM+SMS/GPRS) User Manual (Version 3.1N) Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only. - Page 2 1. Accessories: Please check the accessories before using. Pictures are for indication and illustration purposes only. 2. Features: ● GSM 850/900/1800/1900 Quad band ● Wide for voltage input range: 9-36vDC ● GPS continuous positioning, GPRS timing interval ● Check location via SMS ●...
-
Page 3: Interface Introduction
battery) ● Compatible with external connection through (serial port) ●Geo-fence via sms command 2.1 Red LED (power/working status) LED Status Meaning Flashing (interval 0.1s) Low battery indication Continuously in bright state Charging Slow flashing(interval 0.2s) Full charge Continuously in dark state Low battery / power off Slow flashing(flash 0.1s after every 2s) Working normally... -
Page 4: Method Of Installation
4. Method of installation 4.1. Preparation before installation 4.1.1 Open the packing box to check whether the type of device is correct and whether the accessories are included, or else please contact your distributor. 4.1.2 Choose SIM card: each device needs to insert a GSM SIM card. Please refer to the distributor’s suggestions to choose the SIM card. - Page 5 Please use GSM network SIM card； Power off before installing or removing the SIM card. The SIM card used should be enabled for GPRS. The SIM card used should be enabled for called ID. If there is a power on password, or pin, please cancel it; Ensure the SIM card can send and receive SMS.
-
Page 6: Device Outlet Specification
-in the decorated board below back windshield; Notice: if the windshield is pasted with metal thermal-protective coating or heating coating, It may affect the receiving signal. In this case, please change the installation place. 4.3 Device outlet specification Line No. Specification Color Instruction 1. - Page 7 positive power (+12V). The fine yellow line is connected to the device relay control line. Cut off the positive connection line of the pump; then connect in series to the relay N.C. contact (thick green line 87a) and the other end to relay COM contact (thick green line 30).
-
Page 8: Cautions Of Device Wiring
Please choose 12V or 24V relay according the voltage of the car battery. 5. Cautions of device wiring 5.1 Power/ACC/Tele-cutoff (petrol/electricity) control line (4 pin) 5.1.1 The standard voltage is 9V-36VDC. Please use the power line which provided by the manufacturer. The red line is the positive. The black line is the negative. -
Page 9: Apn And Dns Settings
Any phone numbers can send SMS command to the device as default. 6.1 APN setting To connect default platform www.gpsyeah.com please send the SMS command below: APN,APN’s Name# APN command format: E.g: APN,internet# (“internet” is the APN of carrier) The device will reply “OK” if setting successfully. Note: The APN of some countries have user name and password, you may need to send SMS command as following: APN,APN name,user name,password#... -
Page 10: Delete Specific Number/Set Center Number
6.5 Delete specific number Before deleting specific number, please check its corresponding code. For the code, please SMS “PARAM#” to the device. SMS command to the device to delete the number. SOS,D,serial NO.1,serial NO.2,serial NO.3# “D” means to delete the number, for example: SOS,D,1# means to delete the first number SOS,D,3# means to delete the third number If you want to delete more than one numbers, you can send this command:... -
Page 11: Check Parameter Setting
The command is: CENTER,D# For example: CENTER,D# If set successfully, there is an “OK” reply SMS. NOTE ： Only the SOS number can be used to delete center number successfully. Only SOS phone number can send this command successfully to set the center number. -
Page 12: Sensor Alarm Time Setting
upload positioning data to the platform server every 10s. Users can modify “TIMER,time(second)#”. GPRS time sending interval The time ranges from 10-18000s For example: TIMER,10# It means the device will upload data to the server every 10s. 6.11 Sensor alarm time setting When the vehicle power is off and ACC is in low-level, if ACC is off over 10 minutes, the device will enter sensor alarm state. -
Page 13: Check Location
and GPS LED will flash. Once GPS LED keeps solid light, it means the device has been located and it starts to work. Power off: Just turn off the power switch. The device will begin to upload positioning data to server once inserting a valid SIM card and power on. -
Page 14: Low Battery Alarm
numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the device will upload SOS alarm data to the server. And it will send: ！ ： ： ， Power <Date Time:11-06-17 06> http://maps.google.com/maps?q=N22576713,E113.916585 Note: The specific numbers should be preset, just refer to 6.4 7.5 Low battery alarm When the device is only working with battery, once the internal voltage of... -
Page 15: Over Speed Alarm
enter voice monitoring status. At this time, caller can monitoring the sound in vehicle. Incoming call from non special number will not activate voice monitoring function. Note: To realize this function, please set special numbers beforehand. The SIM card put into the device should be equipped with caller identification. -
Page 16: Web Based Tracking Online Activation
To turn on the over speed function, please send below SMS command: SPEED,Time,Limited speed# Time range（Second）: 5-600s (default as 20s) Limited speed range（km/h）: 0-255 (0 refers to turn off over speed alarm function) Example: SPEED,3,120# Means when the car is moving over 120km/h in average in 3 minutes, the device will send over speed alarm to user. - Page 17 5) Check whether the SIM card supports GPRS; 6) Check the parameter setup, whether the device IMEI number, GPRS sending interval is correct; 9.3 If the device’ GPS function is normal, but can not locate for a long time, please check whether the installation setup of device is correct: 1) Please make sure the GPS antenna face is up;...
-
Page 18: Maintenance Records
4. Please keep this card safely for after-sale service, as well as your receipt. 5. Refer to the table below for the warranty reference. This card is the basic certificate for warranty, please fill it carefully and keep it safely. Name Phone number Address... - Page 19 Maintenance unit Date Fault description Maintenance status IMEI number Serviceman Record two Maintenance unit Date Fault description Maintenance status IMEI number IMEI number...