Related Manuals for Gage Bilt GBP712C
Summary of Contents for Gage Bilt GBP712C
- Page 1 GBP712C INSTALLATION TOOL GAGE BILT PRODUCTS CORP. GAGE BILT 14500 Barber Drive (586) 771-7664 Warren, Mi 48088 (586) 771-2665 Fax MADE IN U.S.A. e-mail:solutions@gagebilt.com / www.gagebilt.com...
-
Page 2: Specifications
TABLE OF CONTENTS Description Page Warnings............................3 Description, Operation and Maintenance................4 Filling & Bleeding ........................5 Trouble Shooting........................6 Overhaul, Disassembly and Parts Lists.................7-8 Nose Assembly Selection Chart....................9 EU Conformity and Warranty....................10 1.94 Ø (49.3mm) 1.36 Ø (34.5mm) 1.84 (46.7mm) 2.25 (57.1mm) 1.50 (38.1mm) 4.74 (120.3mm) - Page 3 TOOL. COMPLETE WITH WARNINGS AND CAUTIONS TO PREVENT SEVERE PERSONAL INJURY OR DAMAGE THE TOOL. CAUTION: GAGE BILT TOOLS ARE APPROVED TO INSTALL HUCK®, AVDEL®, CHERRY®, POP® AND OTHER FASTENERS WHEN USED BY PERSONS WITH SPECIFIC TRAINING OF BLIND RIVET AND LOCKBOLT INSTALLATION EQUIPMENT.
-
Page 4: Maintenance
The GBP712C riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 lbs. air pressure, the GBP712C does not exceed 85 db (A) and consumes 3.9 cfm at 20 cycles per minute. - Page 5 FILLING AND BLEEDING INSTRUCTIONS WARNING: Do not cycle tool without screws or bleeder bottle installed in tool head. Severe personal injury may occur. To replace a small amount of oil in the tool follow steps 19 and 20 below. Should it become necessary to completely refill the tool (as would be required after tool has been dismantled and reassembled), take the following steps.
- Page 6 TROUBLE SHOOTING Providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET. Tool needs to be bled. (See filling and bleeding instructions.) Spring has fatigued, replace. Jaws are stripped or packed with chips. Clean or replace. Incorrect nose tip.
- Page 7 LUBRICATING AND CLEANING PROCEDURE Daily cleaning and lubrication of nose assembly will greatly reduce downtime increase life components. Using sewing machine oil, or an equivalent cleaner/lubricant, follow instructions below. 1. Disconnect tool vacuum line (if equipped). 2. Point nose assembly into oil as shown. 3.
- Page 8 HANDLE To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (712100) first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap screws (402479).
- Page 9 MS90353S & MS90353U MS90354S & MS90354U THE GAGE BILT GBP712C TOOL IS APPROVED TO INSTALL THE ABOVE FASTENERS. *ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER AND 712154 STROKE LIMITER. NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E.
-
Page 10: Declaration Of Conformity
ISO 8662 part 1 ISO 3744 COUNCIL DIRECTIVE: 89/392/EEC, 91/368/EEC 93/44/EEC, 93/68/EEC EQUIPMENT DESCRIPTION: GBP700 SERIES FASTENER INSTALLATION TOOLS MANUFACTURER: GAGE BILT PRODUCTS CORP. SIGNATURE: NAME: BRUCE T. GODFREY CHAIRMAN WARREN, MI U.S.A. JUNE 2003 WARRANTY Seller warrants that all goods covered by this catalog will conform to applicable specifications and will replace, or repair, F.O.B.
Need help?
Do you have a question about the GBP712C and is the answer not in the manual?
Questions and answers