Page 1
® Intel Server Chassis SC5275-E Technical Product Specification C75531-001 Revision 1.2 December, 2005 Enterprise Platforms and Services Division...
Page 2
Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Intel® Server Chassis SC5275-E TPS Table of Contents Table of Contents 1. Introduction .......................... 9 2. Chassis..........................10 System Color ......................10 Front Bezel Features ..................... 10 Security........................10 I/O Panel........................ 11 Chassis Views ....................... 11 3. Chassis Power Subsystem....................14 600W Power Supply ....................
Page 4
Table of Contents Intel® Server Chassis SC5275-E TPS Fixed Hard Drive Bay..................... 25 SCSI Interface ....................... 25 6.2.1 SCSI Hot Swap Backplane Specifications............. 25 6.2.2 FET Short Protection ..................... 26 6.2.3 Device SCSI ID...................... 26 6.2.4 Hard Drive Activity LED ..................26 6.2.5...
Page 5
SATA Hot Swap Drive Bay Upgrade..............38 Appendix A: Chassis Spares and Accessories ..............39 Upgrade and Accessory Parts ....................39 Replacement and Spare Parts for Intel® Server Chassis SC5275-E ........39 Glossary............................. 41 Reference Documents ......................43 Revision 1.2...
Page 6
List of Figures Figure 1. ATX 2.2 I/O Aperture ....................11 Figure 2. Front Closed View of the Intel® Server Chassis SC5275-E ........11 Figure 3. Rear Closed View of the Intel® Server Chassis SC5275-E........12 Figure 4. Front Internal View of the Intel® Server Chassis SC5275-E ........13 Figure 5.
Page 7
Intel® Server Chassis SC5275-E TPS List of Tables List of Tables Table 1. Chassis Dimensions (approximate) ................10 Table 2: Cable Lengths....................... 15 Table 3. Pin-out Baseboard Power Connector P1 ..............15 Table 4. Processor Power Connector P2................... 16 Table 5: Power Signal Connector ....................17 Table 6: PCI Express Connector ....................
Page 8
List of Tables Intel® Server Chassis SC5275-E TPS <This page intentionally left blank.> viii Revision 1.2...
An optional hot-swap SATA upgrade drive bay assembly is available for the Server Chassis SC5275-E. It should be mounted in place of the middle three 5.25-in drive trays in the base, non-redundant chassis models. For the redundant power models, the upgrade accessory should be installed in the lower three 5.25-in drive trays to bring the total number of available...
3 inches (7.62mm) additional side clearance is needed for service access System Color ® The Intel Server Chassis SC5275-E is offered in one color: • Black (GE701), Order code KPTBASE450BLK Front Bezel Features The standard front bezel is molded plastic and attaches to the front of the chassis with a hinge on the right side and two snaps on the left.
All input/output (I/O) connectors are accessible from the rear of the chassis. The SSI E-bay 3.0- compliant chassis provides an ATX* 2.2-compatible cutout for I/O shield installation. Boxed Intel® server boards provide the required I/O shield for installation in the cutout. The I/O cutout dimensions are shown in the following figure for reference.
D. Power supply I/O ports G. Expansion slot covers H. ICMB or external SCSI knockout Serial B port knockout Location to install padlock loop Chassis intrusion switch Figure 3. Rear Closed View of the Intel® Server Chassis SC5275-E Revision 1.2...
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories TP00053C Figure 4. Front Internal View of the Intel® Server Chassis SC5275-E TP00054C Figure 5. Rear Internal View of the Intel® Server Chassis SC5275-E Revision 1.2...
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Chassis Power Subsystem The Server Chassis SC5275-E power supplies are SSI (Server System Infrastructure) compliant. The SSI specifications are provided at the following website: www.ssifourm.org. 600W Power Supply The 600W power supply has 8 outputs: 3.3V, 5V, 12V1, 12V2, 12V3, 12V4, -12V, and 5Vsb (standby).
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories 3.1.2 Output Wire Harness ° Listed or recognized component appliance wiring material (AVLV2), CN, rated min 105 300VDC shall be used for all output wiring. Length From connector No of pins...
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Contact: Molex, 44476-1111 or equivalent Table 4. Processor Power Connector P2 Signal 18 AWG color Signal 18 AWG Color Black +12V1 White 12V1 RS Yellow (24AWG) Black Black +12V1...
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories 3.1.2.3 Power Signal Connector (P14) Connector housing: 5-pin Molex 50-57-9405 or equivalent Contacts: Molex 16-02-0087 or equivalent Table 5: Power Signal Connector Signal 24 AWG Color I2C Clock White...
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Table 9. Floppy Power Connector P6 Signal 22 AWG Color +5VDC Black Black +12V4 Green 3.1.2.8 Right-Angle SATA Power Connector (P12) Connector housing: JWT F6002HS0-5P-18 or equivalent; Table 10: SATA Power Connector...
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories 3.2.1.2 Efficiency The power has an efficiency of 68% at maximum load and over the specified AC voltage. 3.2.1.3 AC Line Fuse The power supply shall have one line fused in the single line fuse on the line (Hot) wire of the AC input.
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Protection Circuits Protection circuits inside the power supply shall cause only the power supply’s main outputs to shutdown. If the power supply latches off due to a protection circuit tripping, an AC cycle OFF for 15sec and a PSON cycle HIGH for 1sec shall be able to reset the power supply.
System Cooling Fan Configuration The cooling sub-system in the Server Chassis SC5275-E consists of two system fans and one power supply fan. A 92mm x 25mm fan located in the front of the fixed hard drive cage draws fresh air into the chassis from the front and provides cooling for the hard drive bay. A 120mm x 38mm fan provides cooling at the rear of the chassis, exhausting warm air out of the system.
Latest BIOS and FRUSDR version is required to be configured for proper performance. In addition, it is recommended that system fans be connected to the Intel® server board SYS Fan header #2 and SYS Fan header #3 for the chassis fans for SE7525GP2 or Intel® Server Board SE7320SP2.
Intel product code APTWKT2COOLKIT (Intel MM # 861825 The Intel® Workstation Cooling Kit can be used to retrofit either a new or existing Intel® Server Board SE7525GP2 or Intel® Server Board SE7320SP2 in the Intel® Entry Server Chassis SC5275-E. Do not install the Intel® Workstation Cooling Kit in systems that have a passive heat sink solution.
System Peripheral Bays 3.5-in Peripheral Drive Bay The Server Chassis SC5275-E provides for the installation of a 3.5-in peripheral, such as a floppy drive, below the 5.25-in peripheral bays. The bezel must be removed prior to floppy drive installation. When a floppy drive is not installed, a snap-in EMI shield must be in place to ensure regulatory compliance.
Hard Disk Drive Bays Fixed Hard Drive Bay The Server Chassis SC5275-E comes with a removable hard drive bay that can accept up to six cabled 3.5-in x 1-in hard drives. Power requirements for each individual hard drive may limit the maximum number of drives that can be integrated into a Server Chassis SC5275-E.
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Power control on the LVD SCSI backplane supports the following features. 1. Spin-down of a drive when failure is detected and reported (using enclosure services messages) via the SCSI bus. An application or RAID controller detects a drive-related problem that indicates a data risk.
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories Green Green 6.2.5 Hard Drive Fault LED The hot-swap controller (HSC) is responsible for turning the drive fault LEDs on or off according to the states specified via commands received from the SAF-TE controller and the IMB. The drive fault LEDs are 4-terminal dual-color (yellow and green) and indicate the failure status for each drive.
Status LED. The Server Chassis SC5275-E provides a 34-pin cable option with the chassis kit. A 34-pin Entry Ebay SSI (rev 3.0) front panel header for Intel® server boards is located on the back of the front panel. This allows for connection of a 34-pin ribbon...
Intel® Server Chassis SC5275-E TPS Appendix A: Chassis Spares and Accessories cable for use with SSI rev 3.0-compliant server boards. The connector cable is compatible with the 24-pin SSI standard. When the hot-swap drive bay is installed, a bi-color hard drive LED is located on each drive carrier (six total) to indicate specific drive failure or activity.
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS BLINK Power fault; Fan fault; Non-critical temperature or voltage fault Fatal error during POST For additional details about front panel functions supported for a specific board, refer to the individual server board specifications.
(SCSI Card Add-in cable, AXXEXTSCSICBL). I/O Panel Connectors The Server Chassis SC5275-E provides an ATX 2.2 and SSI E-bay 3.0-compliant I/O aperture for the backside I/O. The specific panel used will be provided in the boxed server board kit. The following are typical panel connections: •...
• Intel® Server Board SE7520BD2 Product Regulatory Compliance The Server Chassis SC5275-E is designed and tested to meet the standards and regulations listed in the following sections when configured with the Intel® server boards specified. Product Safety Compliance The Server Chassis SC5275-E complies with the following safety requirements: •...
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS All cables used to connect to peripherals must be shielded and grounded. Operation with cables, connected to peripherals that are not shielded and grounded, may result in interference to radio and TV reception.
The BSMI Certification number and the following warning are located on the product safety label, which is located on the bottom side of the chassis. Installation of the Intel® Workstation Acoustic Kit does not effect original compliance to Safety or EMC requirements. Refer to the system product guide for details on regulatory information.
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS 11. Reliability, Serviceability, and Availability 11.1 MTBF Calculated Mean Time Between Failures (MTBF) at maximum configuration has been calculated at 74,000 hours for KDK at 35 degrees C. Table 18. MTBF Calculations...
The optional hot swap SCSI six-drive bay, Product Code AXX6SCSIDB, is available for all of the Server Chassis SC5275-E. It supports up to six 1-inch single connector attachment (SCA) low- voltage differential SCSI (LVD) hard drives to enhance serviceability, availability, and upgradeability of the system.
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS Figure 13. External SCSI Adapter Cable Detail 12.3 SATA Hot Swap Drive Bay Upgrade The SATA Hot Swap Drive Bay Kit, Product Code AXX6SATADB, includes a SATA hot swap drive bay with mounting hardware.
SE7320SP2/Intel® Server Board SE7525GP2 boards only and Inte® Server Chassis SC5275-E. Improves system cooling and acoustics. Includes 2 heatsinks, retention mechanisms, fans spacers, cooling duct, screws and documentation. Replacement and Spare Parts for Intel® Server Chassis SC5275-E Product Code MM # Qty. Description...
Page 40
Appendix A: Chassis Spares and Accessories Intel® Server Chassis SC5275-E TPS FHD3PS450 844924 7 35858 15351 5 Non-redundant 600W Power Supply for Intel® Server Chassis SC5275-E FSATAHSDBBRD 85327 007358-581 16062 9 Spare serial ATA backplane board. Revision 1.2...
Advanced Configuration and Power Interface. Advanced technology extended (motherboard type). Best Known Method – a document, created by an Intel organization that details the proper or customary steps used to perform a specific task (e.g., operating system installation). Baseboard Management Controller – Provides monitoring, alerting, and logging of critical system information obtained from embedded sensors on the baseboard.
Page 42
Operating System Peripheral Component Interconnect Power Factor Correction Revolutions Per Minute Redundant Power Supply Processor Wind Tunnel – Active cooling device included with the Intel® Boxed XeonTM Processors SAF-TE SCSI Accessed Fault –Tolerant Enclosure SATA Serial AT-Attachment interface Single connector attachment.
Need help?
Do you have a question about the SC5275-E and is the answer not in the manual?
Questions and answers