ESAB Origo Tig 3001i Instruction Manual
  1. Manuals
  2. Brands
  3. ESAB Manuals
  4. Welding System
  5. Origo Tig 3001i
  6. Instruction manual

ESAB Origo Tig 3001i Instruction Manual

Hide thumbs Also See for Origo Tig 3001i:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Instruction Manual
Origo™
Tig 3001i, Tig 3001iw
Instruction manual
Valid for: serial no. 840-xxx-xxxx, 950-xxx-xxxx, 039-xxx-xxxx
0460 742 001 GB 20170310

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Origo Tig 3001i and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ESAB Origo Tig 3001i

Summary of Contents for ESAB Origo Tig 3001i

  • Page 1 Origo™ Tig 3001i, Tig 3001iw Instruction manual Valid for: serial no. 840-xxx-xxxx, 950-xxx-xxxx, 039-xxx-xxxx 0460 742 001 GB 20170310...

  • Page 3: Table Of Contents

    TIG welding ....................MMA welding..................... MAINTENANCE ..................... 15 Power unit ....................Welding torch.................... FAULT TRACING................... 16 ORDERING SPARE PARTS ................17 DIAGRAM ......................ORDERING NUMBERS ..................ACCESSORIES ....................Rights reserved to alter specifications without notice. 0460 742 001 © ESAB AB 2017...

  • Page 4: Safety

    Data Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
  • Page 5 • Protect your eyes and body. Use the correct welding screen and filter lens and wear protective clothing. • Protect bystanders with suitable screens or curtains. NOISE - Excessive noise can damage hearing Protect your ears. Use earmuffs or other hearing protection. 0460 742 001 - 5 - © ESAB AB 2017...
  • Page 6 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. 0460 742 001 - 6 -...

  • Page 7: Introduction

    2 INTRODUCTION INTRODUCTION Tig 3001i is a TIG welding power source, which can also be used for MMA welding. ESAB accessories for the product can be found in the "ACCESSORIES" chapter of this manual. Equipment Tig 3001i can be supplied with or without cooling unit.

  • Page 8: Technical Data

    Dimensions l × w × h 625 × 249 × 423 mm with cooling unit 714 × 249 × 693 mm Weight 33.5 kg with cooling unit 54 kg Insulation class transformer 0460 742 001 - 8 - © ESAB AB 2017...
  • Page 9 50 Hz 0.82 kW 1 l/min 0.39 MPa at 60 Hz 0.76 kW 1 l/min 0.44 MPa Coolant ESABs ready mixed coolant. See the "ACCESSORIES" chapter of this manual. 0460 742 001 - 9 - © ESAB AB 2017...

  • Page 10: Installation

    4 INSTALLATION INSTALLATION The installation must be carried out by a professional. Lifting instructions Location Position the welding power source such that its cooling air inlets and outlets are not obstructed. 0460 742 001 - 10 - © ESAB AB 2017...

  • Page 11: Mains Supply

    The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. They may not be applicable in other countries: make sure that the cable area and fuse sizes comply with the relevant national regulations. 0460 742 001 - 11 - © ESAB AB 2017...

  • Page 12: Operation

    5 OPERATION OPERATION General safety regulations for handling the equipment can be found in chapter "SAFETY". Read through before you start using the equipment! 0460 742 001 - 12 - © ESAB AB 2017...

  • Page 13: Connections And Control Devices

    The fans start again when welding restarts. The fans run at reduced speed for welding currents up to 110 A, and at full speed for higher currents. 0460 742 001 - 13 - © ESAB AB 2017...

  • Page 14: Overheating Protection

    • an argon gas regulator • tungsten electrode MMA welding For MMA welding, the power source is supplemented with: • welding cable with electrode clamp, see chapter "ACCESSORIES" 0460 742 001 - 14 - © ESAB AB 2017...

  • Page 15: Maintenance

    (reduced pressure) once a year. Clogged or blocked air inlets and outlets otherwise result in overheating. Welding torch Wear parts should be cleaned and replaced at regular intervals in order to achieve trouble-free welding. 0460 742 001 - 15 - © ESAB AB 2017...

  • Page 16: Fault Tracing

    • Check that the correct current value is set. • Check that the correct electrodes are being used. • Check the main power supply fuses. • Check gas flow and gas quality. 0460 742 001 - 16 - © ESAB AB 2017...

  • Page 17: Ordering Spare Parts

    Repair and electrical work should be performed by an authorised ESAB service technician. Use only ESAB original spare and wear parts. Spare parts and wear parts can be ordered through your nearest ESAB dealer, see the back cover of this document. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list.

  • Page 18: Diagram

    DIAGRAM DIAGRAM 0460 742 001 - 18 - © ESAB AB 2017...
  • Page 19 DIAGRAM 0460 742 001 - 19 - © ESAB AB 2017...

  • Page 20: Ordering Numbers

    CoolMidi 1000 0459 839 033 Spare parts list Origo Tig 3001i 0460 032 1 Instruction manual Control panel Origo TA23 0459 945 1 Instruction manual Control panel Origo TA24 0460 742 001 - 20 - © ESAB AB 2017...

  • Page 21: Accessories

    0460 565 880 Trolley with four wheels 0278 300 401 Insulating bushing for guide pin, included in trolley 0460 911 880 Mounting brackets 0460 459 880 Protection frame Only for air version 0460 742 001 - 21 - © ESAB AB 2017...
  • Page 22 0456 855 881 Water flow guard 0.7 l/min 0465 720 002 ESAB ready mixed coolant (10 l / 2.64 gal) Use of any other cooling liquid than the prescribed one might damage the equipment. In case of such damage, all warranty undertakings from ESAB cease to apply.
  • Page 23 Tig torch TXH 200 8 m 0460 013 840 Tig torch TXH 250w 4 m 0460 013 880 Tig torch TXH 250w 8 m More information on Tig torches can be found in separate brochures. 0460 742 001 - 23 - © ESAB AB 2017...
  • Page 24 ESAB subsidiaries and representative offices Europe THE NETHERLANDS North and South America SOUTH KOREA ESAB Nederland B.V. ESAB SeAH Corporation AUSTRIA Amersfoort ARGENTINA Kyungnam ESAB Ges.m.b.H Tel: +31 33 422 35 55 CONARCO Tel: +82 55 269 8170 Vienna-Liesing Fax: +31 33 422 35 44...

This manual is also suitable for:

Origo tig 3001iw

Table of Contents