ESAB Origo Tig 3001i Instruction Manual
Welding power source
Hide thumbs
Also See for Origo Tig 3001i:
- Instruction manual (32 pages) ,
- Instruction manual (24 pages) ,
- Service manual (76 pages)
Subscribe to Our Youtube Channel
Related Manuals for ESAB Origo Tig 3001i
Summary of Contents for ESAB Origo Tig 3001i
- Page 1 Origo™ Tig 3001i Instruction manual 0460 742 001 GB 20110627 Valid for serial no. 840-xxx-xxxx, 950-xxx-xxxx, 039-xxx-xxxx...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be ob... - Page 5 A equipment in those locations, due to conducted as well as radiated disturbances. CAUTION This product is solely intended for arc welding. CAUTION Read and understand the instruction manual before installing or operating. - 5 - © ESAB AB 2008 bt37e...
-
Page 6: Introduction
For further information contact the nearest ESAB dealer. INTRODUCTION Tig 3001i is a TIG welding power source, which can also be used for MMA welding. ESAB's accessories for the product can be found on page 17. Equipment Tig 3001i can be supplied with or without cooling unit. -
Page 7: Technical Data
2) Valid for power sources with VRD specification on the rating plate.The VRD function is explained in the instructions for the control panel, if the panel has that function. Mains supply, S sc min Minimum short circuit power on the network in accordance with IEC 61000-3-12 - 7 - © ESAB AB 2008 bt37e... -
Page 8: Installation
Equipment marked IP23 is designed for indoor and outdoor use. Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. INSTALLATION The installation must be executed by a professional. Lifting instructions - 8 - © ESAB AB 2008 bt37e... -
Page 9: Location
C MCB 16 A NOTE! The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. Use the welding power source in accordance with the relevant national regulations. - 9 - © ESAB AB 2008 bt37e... -
Page 10: Operation
OPERATION General safety regulations for the handling of the equipment can be found on page 4. Read through before you start using the equipment! - 10 - © ESAB AB 2008 bt37e... -
Page 11: Connections And Control Devices
The fans start again when welding restarts. The fans run at reduced speed for welding currents up to 110 A, and at full speed for higher currents. - 11 - © ESAB AB 2008 bt37e... -
Page 12: Overheating Protection
(reduced pressure) once a year. Clogged or blocked air inlets and outlets otherwise result in overheating. Welding torch Wear parts should be cleaned and replaced at regular intervals in order to achieve trouble-free welding. - 12 - © ESAB AB 2008 bt37e... -
Page 13: Fault-Tracing
Repair and electrical work should be performed by an authorized ESAB serviceman. Use only ESAB original spare and wear parts. Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - 13 - ©... -
Page 14: Diagram
Diagram - 14 - © ESAB AB 2008 bt37e... - Page 15 Diagram - 15 - © ESAB AB 2008 bt37e...
-
Page 16: Ordering Number
TA24 and cooling unit CoolMidi 1000 0459 839 033 Spare parts list Origot Tig 3001i 0460 032 1 Instruction manual Control panel Origot TA23 0459 945 1 Instruction manual Control panel Origot TA24 - 16 - © ESAB AB 2008 bt37o... -
Page 17: Accessories
Protection frame ......0460 459 880 Only for air version Cooling unit CoolMidi 1000 ....0460 490 880 - 17 - © ESAB AB 2008 bt37a... - Page 18 Handy 300 ....... 0700 006 888 - 18 - © ESAB AB 2008 bt37a...
- Page 19 Tig torch TXH 250w 8 m ....0460 013 880 More information on Tig torches can be found in separate brochures. - 19 - © ESAB AB 2008 bt37a...
- Page 20 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the Origo Tig 3001i and is the answer not in the manual?
Questions and answers