Advertisement
Quick Links
T5 Pro/T5
Professional Access Control Reader
Quick Guide
V2.0
Anviz brand and product are trademarked and
protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com, or send email to sales@anviz.com for more help.
©2018 Anviz Global Inc. All Rights Reserved.
1. Package list
Reader
Instruction Package
Accessory Package
2. Installation Diagram
Installation Steps:
Drill holes in the wall and follow the hole position
on back panel.
Install and fix back panel, connect related cables.
Fix access control reader.
3. Wiring Instruction
The interface marked with
for specific models,
J8
Please according to the practical device to wire.
Function
Power
J9
Function
J9
Wiegand
Output
J8
P
2
RJ45(TCP/IP)
RS485
Relay states
6
COM
P
2
Relay
7
NC
12V COM
Select either
8
NO
P2
12 volt out on
COM or voltage
free contact.
Function
6
COM
P
2
Relay
7
NC
(DC12V)
12V COM
8
NO
(DC12V)
Door Sensor
Exit Button
Relay
Please carefully follow this wiring diagram, If the reader gets damaged by incorrect wiring
Important Notice
then your warranty will be void.
· 1 ·
4. Access Control Reader & Power Supply
12V
COM
J8
J9
P2
RJ45 USB
Relay State
Connector Jack
Access Control Power Supply
5. Access Control Reader & Controller 6. Communicate with PC
PIN
Description
1
DC12V
Port
J8
2
GND
PIN
1
Function
Power Supply
+12V GND GND
Connector
PIN
Description
1
Wiegand DATA0 Output
2
Wiegand DATA1 Output
3
GND
4
RS485A
5
RS485B
6
GND
Description
PIN
1
Trigger Input
2
Trigger Input
3
4
GND
5
GND
6
COM
Mark
+12V GND
7
NC
NO
8
Switch Power
J8
Port
J8
P2
Port
PIN
1
2
8
7
6
5
4
3
2
1
PIN
1
2
8
7
12V
COM
Exit
Door
Power Supply
Output Controller
Function
Power Supply
Output Controller
GND
Function
Button
sensor
Relay State
NO
NC
COM GND
Connector
+12V
GND
NO
NC
Connector
+12V GND
OPEN DOOR
+
+
Door Sensor
+
Diode
Power on
to unlock
+
Mark
+12V GND
Mark
+12V
GND
PUSH
NO
GND
NC
+
Switch Power Supply
Power off to unlock
J9
2
6
5
4
3
2
1
RS485
Wiegand Output
GND
D1
D0
RS485B RS485A
TCP/IP
GND
D1
D0
Mark
Mini-USB
（Note: Please verify master card to
enable the USB communication function)
Access control
· 2 ·
P2
6
5
4
3
2
1
Exit
Door
GND
Button
sensor
COM GND
OPEN DOOR
Diode
+
Power off
to unlock
Power on
to unlock
Door Sensor
RS485
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Anviz T5 Pro
Summary of Contents for Anviz T5 Pro
- Page 1 Unauthorized use is prohibited. Mark +12V GND Relay For more information, please visit www.anviz.com, or send email to sales@anviz.com for more help. ©2018 Anviz Global Inc. All Rights Reserved. Mini-USB （Note: Please verify master card to Please carefully follow this wiring diagram, If the reader gets damaged by incorrect wiring...
- Page 2 10. Function button Reader Appearance Add Card Only: ( Operation Steps show as figure 1.2) Continue to register Function Button After registered you can continue register another user or swipe Underneath: Press the button until heard beeps, that eliminate Enroll Card and Delete Card information Enroll Card save and exit.
Need help?
Do you have a question about the T5 Pro and is the answer not in the manual?
Questions and answers