Revisions To This Manual - Magtrol HD-106 User Manual

The contents of this manual are subject to change without prior notice. Should revisions be necessary, updates to all
Magtrol User's Manuals can be found at Magtrol's web site at www.magtrol.com/support/manuals.htm.
Please compare the date of this manual with the revision date on the web site, then refer to the manual's Table of
Revisions for any changes/updates that have been made since this edition.
REVISION DATE
4th Edition, revision O – May 2018
TABLE OF REVISIONS
Date Edition
05/22/18 4th Edition - rev. O
02/18/16 4th Edition - rev. N
06/11/15 4th Edition - rev. M
05/11/15 4th Edition - rev. L
09/04/14 4th Edition - rev. K
06/09/14 4th Edition - rev. J
02/26/14 4th Edition - rev. I
06/01/12 4th Edition - rev. H
05/21/12 4th Edition - rev. G
10/07/08 4th Edition - rev. F
08/31/07 4th Edition - rev. E
08/31/07 4th Edition - rev. E
08/31/07 4th Edition - rev. E
06/11/07 4th Edition - rev. D
03/12/07 4th Edition - rev. C
03/12/07 4th Edition - rev. C
02/02/07 4th Edition - rev. B
02/02/07 4th Edition - rev. B
06/28/06 4th Edition - rev. A
01/23/06 4th Edition
01/23/06 4th Edition
01/23/06 4th Edition
10/12/05 3rd Edition - rev. D
10/12/05 3rd Edition - rev. D
02/24/05 3rd Edition - rev.C
12/09/04 3rd Edition - rev.B
03/11/04 3rd Edition - rev. A
12/08/03 3rd Edition
10/27/03 2nd Edition - rev. E

Revisions To This Manual

Change
6510e/6530 Power Analyzer references changed to 7500 Series
Power Analyzer.
HD-805 Dynamometer regulator setting updated for maximum air flow
cooling.
Speed sensor board schematic added for 2015 and later
dynamometers.
Compressed air regulator setting changed for HD-800 dynamometer.
Updated description of booster power amplifier.
Note added concerning operation at continuous power rating for long
intervals and high temperatures.
All referneces to DSP6001 changed to DSP7000
Dimensions were updated on the data sheet for the HD-800 and HD-
810 model dynamometers
Part number for the 88M007 and 88M070 cables was changed to
88M007-0150 and 88M070-0150
Temperature conditions for maximum power absorption
Updated electrical power and fuse ratings
New resistance and current values for HD-106
Added note about circuitry between connector and brake coil
Deleted: Analog Outputs
Updated calibration drawings and procedure
Added new section: "Calibration Beams and Weights"
New "A", "P" and "Q" dimensions for HD-700 series dynamometers
Change in torque, speed and power ratings.
Change in power and speed ratings for HD-805.
All HD and ED data sheets condensed to one single data sheet.
HD-515 (compressed air cooled) dynamometer added to product line.
New resistance and current values for HD-500 and HD-505
Note to "call factory" for HD-805 power and speed ratings
Change in power rating (5 minutes) for HD-800
Hearing safety warnings added
Electrical power and fuse ratings added to data sheets
5410 Torque/Speed Readout and 5200/5210 Power Supply removed
from manual/open-loop test system configurations
HSD Series High Speed Dynamometers discontinued
Change in maximum torque rating for HSD-710-8N
ii
Section(s)
throughout manual
4.1.3.2.1
B.2
1.3, 4.1.3.2.1
5.6.1
4.3.1
throughout manual
1.3
1.3, 3.3.1, 3.3.2
4.1.3.1
1.3
8.1.3.1, 8.1.3.2
8.1.3.1
7.2, 1.3
6.4
6.2
1.3
1.3, 4.1.3.1
1.3, 4.1.3.1
1.3
1.3, 2.2, 3.3.3,
3.3.3.2, 4.1.3.1,
4.1.3.2.1, 8.1.3.1,
8.1.3.2
8.1.3.1, 8.1.3.2
1.3.3, 4.1.3.1
1.3.3, 4.1.3.1
2.2, 3.3.3.1, 4.1.1,
4.1.3.2.2
1.3.1–1.3.4
1.3.1–1.3.4, 3.3.1
throughout manual
1.3.5, 4.1.3.1