Canon iPF671 Service Manual page 235

Code
Panel display
(last 4 digits)
(Large LCD)
2E32 Insufficient paper
for job
2E33 Roll Paper
(Paper type)
(Paper size)
Load Roll Paper
Stop Printing
Roll 1(Upper)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.
2E34 Roll 2 (Lower)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.
Roll 2 (Lower)
is selected.
Press Load/Eject
and load a roll.
2E35 Roll printing
is selected.
Roll printing
is selected.
Press Load/Eject
and load a roll.
2E36 Roll printing
is selected.
Press Load/Eject
and load a roll.
2E37 Roll printing
is selected.
Roll 1 (Upper)
is selected.
Press Load/Eject
and load a roll.
2E38 Roll 2 (Lower)
is selected.
Press Load/Eject
and load a roll.
2E39 The Roll 2 (Lower) is
empty.
Lift the release
lever and replace
the roll.
The roll (XX) is empty.
Press OK.
2E3A Roll1 jammed. Manually
rewind the
roll all the way
and press OK.
Roll1 (Uppr) jammed.
Manually rewind the
roll all the way
and press OK.
Panel display
Explanation/Detection sequence
(Small LCD)
All of the following conditions have been
met at the start of external printing:
-[ON] has been selected for [Remaining
Roll Paper Detection].
-Among the paper size settings coded in the
print data, the paper length exceeds the
remaining length of roll paper.
-Automatic roll feed to another roll paper
slot which is not the current feeding path,
out of the 2 slots the printer has, is not
available.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When paper has not been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an
error of upper roll occurs.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When no paper has been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an
error of upper roll (2E33) occurs.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When no paper has been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an
error of upper roll (2E33) occurs.
* This is a message that appears when
paper type/ size specification does not exist
due to HPGL format etc.
Paper mismatch (roll paper)
No roll paper has been fed when
performing internal printing.
Paper mismatch (roll paper) (lower)
No roll paper was fed when internal
printing with the specified roll paper
(lower) was started.
Paper mismatch (roll paper) (Upper)
No roll paper has been fed when a job with
roll paper specification is received.
Paper mismatch (roll paper)
No roll paper was fed when the job
specified with upper roll paper was
received.
Paper mismatch (roll paper)(Lower)
No roll paper has been fed when a job with
lower roll paper specification is received.
No roll paper available (trailing edge of roll
paper detected)
-Detected that cut sheet sized paper has
been fed at the roll paper feeding slot.
-The trailing edge of paper was detected by
the Paper detection sensor/ Media sensor
sensor during operation in which roll paper
was used.
-The spool stopped rotating during paper
loading or printing
(XX: Upper roll paper/ Lower roll paper)
During upper roll paper feeding operation,
the paper was fed with the roll feed sensor
detecting the paper, but the paper detection
sensor/ media sensor sensor could not
detect the paper and the operation timed
out.
Chapter 6
Remedial Action
Replace the roll paper.
Load roll paper.
1. Select "load a roll" and follow
instruction on the panel.
2. Select "stop printing," or stop
printing by pressing stop button.
3. Release the release lever and load
the paper.
Load roll paper.
Load roll paper.
Load roll paper.
Load roll paper.
1. Select "load a roll" and follow
instruction on the panel.
2. Select "stop printing," or stop
printing by pressing stop button.
3. Release the release lever and load
the paper. (This step 3 is only for 800/
8000/9000 series.)
Load roll paper.
1. Replace the roll paper
-Check paper sensor R (I/O mode).
2. Is the paper fed successfully (under
a negative load or any other
influence)?
Manually rewind the paper and reload.
6-25