Canon iPF671 Service Manual page 227

Code
Panel display
(last 4 digits)
(Large LCD)
2827 Execute printhead
2828 cleaning. If this
2829 message is still
displayed, replace
Printhead.
Execute printhead
cleaning. If this
message is still
displayed, replace
Printhead.
[Stop: Stop Printing
Execute printhead
cleaning. If this
message is still
displayed, replace
printhead .
Printing stopped.
[OK]
282A CR MOTOR TUNING
ERROR :PRESS OK
282B CR VIBRATION
ERROR :PRESS OK
282D Left printhead
error.
Turn off printer,
wait, then
turn on again.
282E !Printhead error
Turn off printer,
wait, then
turn on again.
2830 Left printhead
error.
Open top cover and
replace the left
printhead.
2832 Hardware error
03130031-2832
Turn off printer,
wait, then
turn on again.
2833 Hardware error
03130031-2833
Turn off printer,
wait, then
turn on again.
2834 !Unknown printhead. Open
top cover and re-install
printhead.
2901 Mail box
nearly full.
Delete unwanted data
The mail box is
nearly full. Delete
unwanted jobs.
2902 Mail box full.
Now printing
without saving data.
2905 Mail box full.
Delete unwanted data
on your computer
to resume printing.
Press Stop
to cancel printing.
The mail box
is full.
Delete unwanted data
from your computer
to continue.
Panel display
Explanation/Detection sequence
(Small LCD)
Printhead non-discharge error
(Replace printhead/ continued printing not
allowed)
At start of printing the number of non-
ejecting nozzles is more than 320 per color
(1 chip).
2827: Both L and R, or single printhead
model
2828: R printhead
2829: L printhead
* For the detailed head non-ejection errors,
see section 280C.
(If Setting of SERVICE MODE >
SETTING >HEAD WARNING is off, the
error code is 280E.)
Carriage motor identification processing
(rotation adjustment) failed (for Service
mode)
When processing carriage motor
identification (rotation adjustment),
carriage vibration has been detected (for
Service mode).
Printhead error detected (L head only).
Displayed when an abnormal temperature
rise of printhead has been detected to
prompt you to restart.
Temperature rising detected by particular
ink pre-injection before printing was
judged abnormal.
Printhead error detected (L head only).
Displayed when restarting after detection
of error 282D to prompt you to replace
printhead L.
VHT leak detection error of right printhead
or of a single printhead, in case of VHT
exceeds rated value or falls below the rated
value.
VHT leak detection error of left printhead,
in case of VHT exceeds rated value or falls
below the rated value.
Printhead contact failure is detected after
the
printhead installation.
The available size of the permanent area of
the hard disk space has fallen to less than 1
GB.
The hard disk has run out of free space,
disabling copy printing or error recovery.
A job save has been executed when the
available size of the permanent area of the
hard disk space was lost.
Cancel the job.
Chapter 6
Remedial Action
1. Execute cleaning.
2. Replace printhead.
Error is cleared by OK button.
1. Check installation of carriage or
carriage belt.
2. Clean the carriage main rail (Do not
oil it.)
3. Replace the carriage motor.
Error is cleared by OK button.
1. Check installation of carriage or
carriage belt.
2. Clean the carriage main rail (Do not
oil it.)
3. Replace the carriage motor.
After restarting, replace the printhead
L.
1. Replace the printhead.
2. Replace the main controller PCB.
Replace the printhead L.
iPF6300/6400 Series
iPF8300/8400/9400
Series
Replace right or left
printhead.
1. Remove and reinstall the printhead.
2. Replace the printhead.
3. Replace the carriage unit.
4. Replace the main controller PCB.
Reorganize data.
Reorganize data.
Reorganize data.
6-17