Titan Speeflo PowrTex 300DD Owner's Manual
Titan Speeflo PowrTex 300DD Owner's Manual

Titan Speeflo PowrTex 300DD Owner's Manual

Texture sprayers

Advertisement

Quick Links

PowrTex 300
Model Numbers:
PowrTex 300
PowrTex 600
Printed in the U.S.A.
SPEEFLO
Texture Sprayers
These sprayers are for
use with water-based
materials only!
600-130
DD
600-140
DD
Owner's Manual
For professional use only
Do not use this equipment
before reading this manual!
/ 600
DD
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0528918A
0110
DD

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Speeflo PowrTex 300DD and is the answer not in the manual?

Questions and answers

Summary of Contents for Titan Speeflo PowrTex 300DD

  • Page 1 Model Numbers: NOTE: This manual contains important PowrTex 300 600-130 warnings and instructions. Please read and retain for reference. PowrTex 600 600-140 Printed in the U.S.A. © Titan Tool Inc. All Rights Reserved. Form No. 0528918A 0110 •...
  • Page 2 • Hearing protection is recommended for extended use. • Always wear appropriate gloves, eye protection, clothing and a respirator or mask when spraying. • Do not aim the gun at or spray any person or animal. © Titan Tool Inc. All rights reserved.
  • Page 3: Table Of Contents

    PowrTex Spray Gun Maximum Operating Pressure ..100 PSI (0.69 MPa) Maximum Air Pressure ....100 PSI (0.69 MPa) Weight ......... 2.2 lbs. (1 kg) © Titan Tool Inc. All rights reserved.
  • Page 4: General Description

    Turning the fluid adjustment knob counterclockwise lengthens the trigger pull and increases the flow of material to the texture nozzle. © Titan Tool Inc. All rights reserved.
  • Page 5: Operation

    While triggering the gun, tighten the nozzle nut securely. IMPORTaNT: always pull the spray gun trigger when tightening the nozzle nut. Failure to pull the trigger can result in damage to the texture nozzle and gun needle assembly. © Titan Tool Inc. All rights reserved.
  • Page 6: Preparing The Spray Material

    Fine tune the spray pattern using the fluid adjustment knob and air adjustment valve on the spray gun. Refer to the “Spray Gun Operation” section for detailed information on gun adjustments. © Titan Tool Inc. All rights reserved.
  • Page 7: Spraying Technique

    Tighten securely. NOTE: For information on texture nozzle sizes and their recommended uses, refer to the “Texture Nozzle chart” in the Parts List section of this manual. © Titan Tool Inc. All rights reserved.
  • Page 8: Cleanup

    5. Oil the texture shaft assembly using Titan Piston Lube 20. Follow the “Pressure Relief Procedure” found in the (refer to the Accessories section for P/N). Apply several Operation section of this manual.
  • Page 9: Maintenance

    3. If you have any further questions concerning your TITAN 3. Reattach the fluid hose to the fluid outlet fitting. Airless Sprayer, call TITAN: 4. Fill the hopper 1/4 full with clean water.
  • Page 10: Replacing The Diaphragms - Powrtex 600 Dd

    Make sure the manifold is positioned in the same each side of the pump motor. orientation as it was before it was removed. 24. Using the four manifold nuts, screws, and washers, reassemble the delivery manifold to the top of the © Titan Tool Inc. All rights reserved.
  • Page 11: Replacing The Reversing Valve

    Make sure the manifold is positioned in the same orientation as it was before it was removed. 10. Replace the pump onto the sprayer as described in the corresponding “Replacing the Diaphragms” procedure in this section. © Titan Tool Inc. All rights reserved.
  • Page 12: Troubleshooting

    Soak and clean well. No air through gun when pulling Air nozzle passage packed with material Clean the texture shaft passage. trigger Two-stage texture shaft assembly not Clean the texture shaft assembly. functioning properly © Titan Tool Inc. All rights reserved.
  • Page 13 Locate and tighten the fittings where air can be heard escaping. Check the fittings with a soapy water solution, if necessary. Valve has carbon buildup, is worn, or Inspect valve and clean, repair, or replace, if damaged necessary. © Titan Tool Inc. All rights reserved.
  • Page 14: Parts Listings

    Parts List Main assembly — PowrTex 300 (P/N 600-130) © Titan Tool Inc. All rights reserved.
  • Page 15: Compressor

    Warning label —Burn Hazard Item Part # Description Quantity 600-466 Valve kit ............1 600-468 Thermal protector, 15 A, PowrTex 300 ...1 600-469 Thermal protector, 18 A, PowrTex 600 ...1 600-467 Air filter kit ..........1 © Titan Tool Inc. All rights reserved.
  • Page 16: Main Assembly - Powrtex 600 Dd

    Main assembly — PowrTex 600 (P/N 600-140) © Titan Tool Inc. All rights reserved.
  • Page 17: Electrical Schematic

    (includes items 46 and 48–51)) Electrical Schematic NOTE: all electrical work should be performed by an authorized service center. Compressor BLACK Power GREEN Cord Ground screw at switch box Ground ON/OFF screw at Switch switch box WHITE © Titan Tool Inc. All rights reserved.
  • Page 18: Fluid Pump - Powrtex 300 Dd

    Product diaphragm ........2 600-416 Nut (torque to 44 in./lbs.) ......12 600-410 Outer diaphragm disk (torque to 9 ft./lbs.) 2 600-418 Screw ............12 600-411 Diaphragm cover ........2 600-501 O-ring (also included in item #10).....4 © Titan Tool Inc. All rights reserved.
  • Page 19: Fluid Pump - Powrtex 600 Dd

    O-ring (also included in item #9)....4 600-428 Outer diaphragm disk (torque to 9 ft./lbs.) 2 600-440 Screw ............1 600-429 Diaphragm cover ........2 600-436 Washer .............1 600-416 Nut ............8 600-424 Ground lug ..........1 600-435 Fluid valve unit..........4 © Titan Tool Inc. All rights reserved.
  • Page 20: Motor

    Contact washer.........4 600-453 Lip gasket, small ........2 600-451 Screw ............4 600-454 Lip gasket, large ........2 600-450 Silencer .............1 600-445 Bushing guide ...........2 600-446 Discharge side cover ........1 600-443 Shaft ............1 600-419 Screw ............4 © Titan Tool Inc. All rights reserved.
  • Page 21: Powrtex Gun

    Orange peel High Low to medium Pattern Fine to medium simulated acoustics High Low to medium Coarse simulated acoustics Medium High Splatter coat Low to medium Medium to high Knockdown Medium to high © Titan Tool Inc. All rights reserved.
  • Page 22: Air Flow Schematic - Powrtex 300 Dd

    Flow Schematic — PowrTex 300 = Air Flow Radiator Compressor Manifold Relief Valve Double Diaphragm Pump Air Tubing (not shown) © Titan Tool Inc. All rights reserved.
  • Page 23: Air Flow Schematic - Powrtex 600 Dd

    Flow Schematic — PowrTex 600 = Air Flow Compressor Radiator Double Diaphragm Pump Manifold Relief Valve Pressure Regulator 3/8” Air Tubing (not shown) 3/8” Air Tubing Pressure (not shown) Gauge 1/4” Air Tubing (not shown) © Titan Tool Inc. All rights reserved.
  • Page 24: Accessories

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within twelve (12) months after...

This manual is also suitable for:

Speeflo powrtex 600dd

Table of Contents