Titan 330 Owner's Manual
Titan 330 Owner's Manual

Titan 330 Owner's Manual

Airless sprayer

Advertisement

Do not use this equipment before reading this manual!
Model Numbers:
110V Complete
110V Bare
230V Complete
110V Complete
Printed in the U. S. A.
330
Airless Sprayer
704-2000
704-2010
704-2030-CE
704-2000-CE
Owner's Manual
For professional use only
NOTE: This manual contains important warnings
NOTE: This manual contains important warnings
and instructions. Please read and retain for
and instructions. Please read and retain for
reference.
reference.
0901 © 2001 Titan Tool Inc. All rights reserved. Form No. 313-1487, REV C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 330 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Titan 330

  • Page 1 Please read and retain for and instructions. Please read and retain for 230V Complete 704-2030-CE reference. reference. 110V Complete 704-2000-CE Printed in the U. S. A. 0901 © 2001 Titan Tool Inc. All rights reserved. Form No. 313-1487, REV C...
  • Page 2: Table Of Contents

    Do not use plastic drop cloths PREVENTION: when spraying flammable materials. • NEVER aim the gun at any part of the body. • Use lowest possible pressure to flush equipment. © Titan Tool Inc. All rights reserved.
  • Page 3 W- A after the cord type designation. For example, a designation of SJTW-A would indicate that the cord would be appropriate for outdoor use. © Titan Tool Inc. All rights reserved.
  • Page 4: General Description

    10. Move the PRIME/SPRAY valve up to the SPRAY position. Always use a minimum 12 gauge, three-wire extension cord 11. Turn the unit on. with a grounded plug. Never remove the third prong or use an adapter. © Titan Tool Inc. All rights reserved.
  • Page 5: Painting

    6. Trigger the gun to remove any pressure that may still be in the hose. 7. Lock the gun by turning the gun trigger lock to the locked position. 8. Move the PRIME/SPRAY valve down to the PRIME position. © Titan Tool Inc. All rights reserved.
  • Page 6: Spraying

    Shrubs next to houses should be tied back and covered with a canvas cloth. The cloth should be removed as soon as possible. Titan gun extensions are extremely helpful in these situations. Avoid arcing or holding the gun at an angle. This will result in an uneven finish.
  • Page 7: Cleanup

    10. Move the PRIME/SPRAY valve up to its SPRAY position. cleaning solvent. Always contact the supplier of solvents 11. Turn the unit on. for recommendations. 4. If you have any further questions concerning your TITAN WARNING Airless Sprayer, call TITAN: Customer Service (U.S.) .......1-800-526-5362 Ground the gun by holding it against Fax ..........1-800-528-4826...
  • Page 8: Replacing The Motor

    100 hours of use (grease fittings supplied). Brush Clamp Motor Brush and Tube Crankshaft Motor Housing Motor Wires Spring Washer Pinion Gear Insulator Plate Armature Cover Plate Connecting Rod Rear Bearing Housing Front Cover Pump Housing © Titan Tool Inc. All rights reserved.
  • Page 9: Replacing The Motor Starter

    “Parts List” section of this manual for proper wiring of the pressure switch. NOTE: After installation, the pressure may need to calibrated by an authorized Titan service center. © Titan Tool Inc. All rights reserved.
  • Page 10: Servicing The Fluid Section

    16. Thread the pump block mounting screws through the pump block and into the main housing. Tighten securely. 17. Reassemble the foot valve assembly into the pump block. © Titan Tool Inc. All rights reserved.
  • Page 11: Replacing The Transducer

    Housing Handle T-Slot Front Cover Transducer Gasket NOTE: For more detail, part number information, and assembly drawings at larger scale, please see Pump Block the LX -80 Professional Airless Gun Owner's Manual (#313-012). © Titan Tool Inc. All rights reserved.
  • Page 12: Troubleshooting

    2. Needle assembly out of adjustment 2. Adjust 3. Dirty gun 3. Clean Gun does not spray 1. No paint 1. Check fluid supply 2. Plugged filter or tip 2. Clean 3. Broken needle in gun 3. Replace © Titan Tool Inc. All rights reserved.
  • Page 13: Spray Patterns

    1. Tighten contracting (Surge) 2. Not enough hose 2. Use a minimum of 50' (15m) of 1/4" high pressure hose 3. Tip too large or worn 3. Replace with a new or smaller tip © Titan Tool Inc. All rights reserved.
  • Page 14: Français

    • Tous les accessoires doivent être homologués pour une pression égale ou supérieure à 3 200 lb/po2 / 221BAR. Cela s'applique, entre autres, aux têtes de pulvérisation, aux accessoires du pistolet et aux flexibles. © Titan Tool Inc. Tous droits réservés.
  • Page 15 égale ou supérieure à 3 200 lb/po2 / 221BAR. • Ne jamais pulvériser lorsqu'il vente. • Porter des vêtements pour protéger la peau et les cheveux contre tout contact avec la peinture. © Titan Tool Inc. Tous droits réservés.
  • Page 16: Español

    Consulte el manual del motor • Todos los accesorios deben tener una capacidad de 3200 para obtener información completa de seguridad. lb/pulg2 / 221BAR o mayor. Esto incluye las boquillas de atomizador, pistolas, extensiones y mangueras. © Titan Tool Inc. Todos los derechos reservados.
  • Page 17 W-A después de la designación del tipo de cable. Por ejemplo, SJTW-A para indicar que el cable es apropiado para uso en exteriores. © Titan Tool Inc. Todos los derechos reservados.
  • Page 18: Parts Listings

    Parts List Main Assembly © Titan Tool Inc. All rights reserved.
  • Page 19: Motor Assembly

    700-674 End cap..........4 704-092 Leg, left (includes items 2 and 4) ..1 700-781 Drip cup ...........1 700-069 Screw ..........2 700-761 Cord wrap ........1 704-091 Leg, right (includes items 2, 5, and 6) .....1 © Titan Tool Inc. All rights reserved.
  • Page 20: Gear Box Assembly

    Gear Box Assembly © Titan Tool Inc. All rights reserved.
  • Page 21: Suction Set Assembly

    Retaining clip ........1 ON/OFF Switch 704-129 Retaining ring Blue Brown (alternate, included in literature set) Green/Yellow Power Cord 700-1023 Siphon hose (includes items 2, 3, and 6 ....1 755-135 Clip...........1 700-805 Inlet screen ........1 © Titan Tool Inc. All rights reserved.
  • Page 22: Pump Block Assembly

    Groove pin ........1 700-537 Gasket ..........1 NOTE: When using “HOT” solvents, replace Viton o- 221-012 O-ring, Viton........1 ring (item 13) with optional PTFE o-ring (700- O-ring, PTFE ........1 222-012 897). Install with o-ring tool (700-890). © Titan Tool Inc. All rights reserved.
  • Page 23: Fluid Section Assembly

    730-509 Bushing..........1 700-821 Lower seal ..........1 730-510 Lower cage ...........1 762-145 Foot valve ball ........1 762-137 Foot valve seat ........1 762-058 O-ring............1 704-054 Foot valve housing .......1 762-202 Packing tool (not shown) ......1 © Titan Tool Inc. All rights reserved.
  • Page 24: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within...

This manual is also suitable for:

704-2000704-2010704-2030-ce704-2000-ce

Table of Contents