Related Manuals for Peco Pro 12 DFS 52621201
Summary of Contents for Peco Pro 12 DFS 52621201
- Page 1 P P P PTO GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM 2013 - 2015 MODEL YEAR MODEL #: 52621201 OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q047 REV: 2 (06-2018)
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Exhaust Diverter Installation - - - - - - - - - - - - - - - - - 17 Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION Introduction Description Your collection system has been designed to give you a The grass collection system is designed for turf low maintenance, simple, and effective way to collect the maintenance where there is a need to collect the grass grass clippings from your mower. -
Page 6: Installation For Use
Section II - INSTALLATION FOR USE The engine pulley assembly must be installed using an Preparation Of Mower arbor press or equivalent. During installation, opposite bearing inner race must be supported or bearing NOTE: The mower deck PTO belt must be removed damage may occur. -
Page 7: Left And Right Frame Bracket Installation
Remove the rear guard and hardware from the mower frame. Remove the rear right anti-scalp wheel and hardware. Refer to Figure A. Figure A NOTE: X-Diablo, Diablo and DiabloMP series will need Anti-Scalp to have the muffler guard removed and replaced with Wheel muffler guard P#(B0831) in a later step. -
Page 8: Rear Frame Bracket Installation
Rear Frame Bracket Installation Secure the rear frame bracket P#(B0827) to the left and right frame bracket using (2) 3/8”-16 x 1” HHCS P#(K1191) and (2) 3/8”-16 nylon flange locknuts P#(K2038) PER BRACKET. Refer to Figure A. (2) 3/8”-16 x 1” HHCS (2) 3/8”-16 Locknuts PER BRACKET Figure A... -
Page 9: Right And Left Pto Mount Plate Installation
Right and Left PTO Mount Plate Installation Secure the left PTO mount plate P#(B0829) to the right frame bracket using (2) 3/8”-16 x 1” HHCS P#(K1191) and (2) 3/8”-16 nylon flange locknuts P#(K2038). Refer to Figure A and B for reference. Secure the right PTO mount plate P#(B0828) to the right frame bracket using (1) 3/8”-16 x 1”... -
Page 10: Pto Assembly Installation
PTO Assembly Installation Insert the PTO assembly P#(A0623) into the slots on the PTO mount plate assembly. Secure the PTO assembly with (1) mount pin P#(B0274) and (1) hair pin clip P#(K0086). Remove the engine pulley guard and hardware in preparation for the belt installation. -
Page 11: Belt Installation And Adjustment
Connect the kevlar cord belt A59K P#(M0254) from the Belt Installation and Adjustment engine pulley to the lower gear box pulley (Figure D). Loosen the (4) bolts P#(K1191), (2) on each side, that Figure D secure the gear box assembly to the PTO assembly Connect Belt P#(A1803) (Figures A and B). -
Page 12: Cam Assembly Adjustment
Cam Assembly Adjustment The cam assembly P#(A0422), which controls the blower belt tension, comes from the factory pre-adjusted. If the belt is too tight or becomes too loose, remove the hair pin clip P#(K0099) from the belt tension rod P#(K0326) and pull the “L” end of the rod out of it’s hole in the cam assembly. -
Page 13: Main Frame Leg Installation
Main Frame Leg Installation Main Frame Assembly Installation Secure (1) main frame leg P#(B0830) to the left frame Lift the main frame assembly P#(A0995) into position as bracket and (1) main frame leg P#(B0830) to the right shown in Figure A. Secure the main frame assembly to frame bracket using (2) 3/8”-16 x 1”... -
Page 14: Lift Handle Installation
Lift Handle Installation Fasten the ball joint P#(K1442) to the end of the latch NOTE: Before continuing the lift handle installation, rod P#(A0620). Tighten the ball joint to approximately have someone assist you in turning the grass container half way down the threads on the latch rod. Attach the upside down. -
Page 15: Aluminum Grass Container Installation
Aluminum Grass Container Dump Mechanism Adjustment Installation The linkage may be adjusted in two places, at the NOTE: It is recommended that (3) people assist in adjusting screw P#(K1435) and the latch assembly mounting the container. With three people available, two items. -
Page 16: Aluminum Grass Container Exploded View
ALUMINUM GRASS CONTAINER EXPLODED VIEW... -
Page 17: 2-15 Exhaust Diverter Installation
2-15 Exhaust Diverter Installation NOTE: On certain engine models, it is necessary to install an exhaust diverter onto the muffler to prevent the engine exhaust from damaging the PTO assembly or the collection bags. Figure A shows an exhaust diverter P#(J0251) and exhaust clamp kit P#(X1046) installed on the Kawasaki FX850. -
Page 18: Boot Kit Installation
Boot Kit Installation Position the boot plate P#(B0832) onto the top of the The boot kit is designed to work on the 52” and 60” aluminum boot P#(E0025) as shown in Figure A. Secure decks. After attaching the boot plate to the boot, lift the the boot plate to the boot using (3) 3/8”-16 x 1”... -
Page 19: Length Of Hose Adjustment
Length Of Hose Adjustment Lower Hose To Blower Cone Installation The hoses must be cut to fit your machine. Do not cut Slide a pre-assembled hose clamp P#(J1000) over both the hoses until you have tried to fit them on your ends of the lower hose. -
Page 20: Impeller Blade Removal/Replacement
Impeller Blade Removal/Replacement To gain impeller blade (#1) access, first remove the blower cone (#2) from the blower housing, located on Tips on removing impeller blade; the PTO assembly P#(A0623), by removing two blower 1 - Try carefully hitting the base of the impeller blade cone bolts and nuts (#3). -
Page 21: Weight Kit Installation
Weight Kit Installation Lift the weight bar P(B0034) into position underneath A weight kit must be installed to your unit as a the weight bracket. Secure the weight bar using (2) 12”- counterweight for the collection system. This universal 13 U-bolts P#(K0331) and (4) 1/2”-13 nylon flange weight kit is designed to fit all series of Big Dog locknuts P#(K2012). -
Page 22: Exploded Drawing Views And Parts Lists
A1841_01 PTO Arm Assembly... - Page 23 A1941_01 PTO Base Assembly Exploded Parts View...
- Page 24 A1941_01 PTO Base Assembly Exploded Parts List...
- Page 25 A0623 PTO Assembly w/ Small Pulley Guard Exploded Parts View...
-
Page 27: Operating Instructions
SECTION III Disengagement Of The Blower OPERATING A. To disengage the blower, rotate the engagement INSTRUCTIONS handle towards the mower. General Safety WARNING: The blower will continue to spin. DO NOT TOUCH the blower, pulleys, or the belt until the tractor is Only qualified people familiar with this operator’s manual turned off. -
Page 28: Lubrication
If there are any portions of the hose that have been torn or worn through, replace with genuine contain a greaseable zirc fitting. Newer models PECO parts. contain maintenance-free bearings and are without a greasable fitting. After Each Use: 1. -
Page 29: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. # R2008 # R2007 Part #: R1053... - Page 31 NOTES...
- Page 32 P P P PECO PECO PECO PECO PECO 10 WALDEN DRIVE ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...